manualshive.com logo in svg

Amada MAWA-300B-00-00, Руководство по эксплуатации, Страница: 161 / 168

Поделиться
Скачать
Amada MAWA-300B-00-00 Скачать руководство пользователя страница 161

MAWA-300B 

8. Troubleshooting 

8-1 

8. Troubleshooting 

 

(1) Error 

Screen 

When an error occurs in the welding power supply, the Error screen will be displayed on the touch 
panel display.    The error code, error message, condition No. at occurrence of the error, and error 
occurrence time after turning on the welding power supply are displayed. 
After removing the cause of the error, press the “RESET” button on the front panel or enter the 
“RESET” signal.    Then, a recovery can be made from the error status.    If the cause of the error is 
not removed, the Error screen will be displayed again. 
If an error display is disabled because communication with the touch panel display cannot be 
performed, the buzzer of the welding power supply sounds continuously.    Turn on the power supply 
again. 

 

 
(a) SCH  

The condition No. selected at occurrence of an error is displayed. 

 
(b) MESSAGE  

The error code of the current error and an error message are displayed in red characters. 

 
(c) Time 

(min) 

The minutes elapsed after the power supply of the welding power supply is turned on at 
occurrence of an error are displayed. 

 

E03 OVER HEAT ERROR

E01 EMERGENCY STOP

Содержание MAWA-300B-00-00









































































































































































Отзывы:

Нет отзывов