Altigen ACM 6.5 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 502

Altigen ACM 6.5 Скачать руководство пользователя страница 75

Defining System Call Restrictions

MAXCS ACM 6.5 Administration Manual 61

Locking Attacked Extensions

If a user enters eight consecutive invalid passwords when logging on to voice mail or to
activate an extension, MAXCS considers this an attack. To protect your company from
theft of services, you can lock an attacked extension for the period of time you specify
(10 minutes - 23 hours, 59 minutes, and 59 seconds) in the

Password Check

field

group.
To unlock an extension, use the Extension Checker tool that is installed with MAXCS. See
“MAXCS Admin & Extension Security Checker” on page 433.

Blocking All Outgoing Calls

To block all outgoing calls—for example, during the night when no employee is in the
office—check the

Block All Outgoing Calls

check box.

Enabling Hop Off for Tie Trunks

When selected, this function allows users from another system to borrow a PSTN trunk

in this system to make an outbound call over a T1 or VoIP tie trunk.

Figure 10. Hop Off for Tie Trunks

Restricting Tie Trunk Calls

You can set call restrictions on hop-off calls by telling the system to use the same
restrictions as the ones set up for an extension. Using the

Call restriction follows

extension

drop-down list, you can select the extension with the restrictions to use for

the hop-off calls.

Setting 10-Digit Dialing Area Codes

The

10-Digit Dialing Area Code

field lets you define area codes that do not require

dialing a “1” before the area code. To enter an area code, click the

Add

button.

Note:

Applies only to calls that use a trunk access code. For calls using a route access
code, 10-digit dialing area codes need to be configured in the Out Call Routing

Configuration window, Dialing Pattern tab. See “Working on Dialing Patterns” on
page 187.

System B

System A

Tie Trunk:

T1/PRI or VoIP

Outgoing

call on PSTN

Trunk

The call originating on System B hops off over the T1/PRI or VoIP trunk to use the PSTN
trunk in System A. System A must be set up to allow System B to borrow its PSTN trunk.

«
...
73
74
75
76
77
...
»

Содержание ACM 6.5























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов