manualshive.com logo in svg

Altigen ACM 6.5, Руководство администратора, Страница: 189 / 502

Поделиться
Скачать
Altigen ACM 6.5 Скачать руководство пользователя страница 189

Configuring the Virtual MobileExtSP Board

MAXCS ACM 6.5 Administration Manual 175

Double-clicking a channel in the 

Channel Mapping List

 opens the appropriate 

configuration dialog box for that channel. 

•

For information on configuring the T1/E1 trunk, see “Triton T1/E1 Trunk Properties” 
on page 133.

•

For information on configuring the Triton Analog Trunk, see “Triton Analog Trunk GS/
LS Properties” on page 136. 

•

For information on configuring a Triton Analog Line, see “Triton Analog Station Line 
Properties” on page 202.

In the main Board Configuration dialog box for the MAX 1000/2000 board (see Figure 20 

on page 174) clicking the 

Board Configuration 

button opens the following dialog box.

Figure 21. MAX 1000/2000 Board Configuration window

This dialog box displays the board serial number, top access card serial number, bottom 

access card serial number, DSP clock, board ID, physical ID, and logical ID. You can 
choose to configure the board as either T1 or E1, then click 

OK

. Additional steps are 

needed to further configure the CAS or PRI protocol in the Protocol Configuration 

window, shown in Figure 9 and Figure 10. 

Configuring the Virtual MobileExtSP Board

A simulated physical board—MobileExtSP board—is created in the Softswitch server 

when you install the MAXCS system. This single MobileExtSP board handles all mobile 
extensions, including those located in other gateways in a multi-gateway system.
Configuring the virtual MobileExtSP board is discussed on page 248 in the chapter 
“Mobile Extension Configuration.”

Содержание ACM 6.5























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов