manualshive.com logo in svg

Altigen ACM 6.5, Руководство администратора, Страница: 409 / 502

Поделиться
Скачать
Altigen ACM 6.5 Скачать руководство пользователя страница 409

Using SNMP

MAXCS ACM 6.5 Administration Manual 395

The difference between the 

Current Resource Statistics

 window and the 

IP 

Cumulative Traffic Statistics

 window is that the former shows figures only for the 

active

 call (Current Traffic) on a particular IP trunk of the local MAXCS system while the 

other window shows figures for 

all

 calls combined (cumulative traffic).

Resetting Cumulative Statistics

You can reset the 

IP Cumulative Traffic Statistics

 by clicking the 

Reset

 button. Also, 

this window automatically resets all fields to 

0

 when the MAXCS system is shut down 

and restarted. Statistics gathered before the reset are not saved.

Using SNMP

SNMP (Simple Network Management Protocol) is used in network management systems 

to monitor network-attached devices for conditions that warrant administrative 
attention. 
This MAXCS SNMP configuration, used with a third-party management console (see next 
section), helps you see the MAXCS status, so you can use MAXCS more securely. Using 

an SNMPv3 agent, MAXCS sends SNMP traps to the management console when alarming 
conditions are detected.

Note:

The SNMP traps are sent by the Altigen services SPServ (Softswitch up, Softswitch 
down traps), AltiKeep (warm start trap), and AltiServ (all other traps), so those 
services need to be started, or the traps will not be sent.

SNMP Management Console

To use SNMP, you need an SNMP management console that is SNMPv3-supported for 
receiving and collection. If you’re not already using one, AltiGen recommends MG-Soft 
Trap Ringer Professional Edition, available from MGSoft Corporation, at http://www.mg-

soft.com/tringer.html.
You can get help about how to configure an SNMP User Account and Management 
Console Port in that product’s Help system.

Note:

AltiGen’s IANA Private Enterprise Number is 13679.

Configuring MAXCS for SNMP

To configure MAXCS for SNMP, select 

Report > SNMP Configuration

. 

Packets Lost

Number of voice packets that have been lost due to 
prolonged delays, network congestion, or routing 
failure.

Average Jitter 

Average length of delay per voice packet in 
milliseconds. This figure should stay under 100 
milliseconds. A higher figure indicates a longer 
average delay. This number can be used to measure 
the quality of service on the network that connects 
the source and destination sites.

Parameter

Description

Содержание ACM 6.5























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов