Altigen ACM 6.5 Скачать руководство пользователя страница 439 | Manualshive

Страница: 439 / 502

Altigen ACM 6.5 Скачать руководство пользователя страница 439

Setting Up the Client

MAXCS ACM 6.5 Administration Manual 425

4. In the

Line used for

section, select the client extension in the

Phone calls

drop-

down list, and click

OK

.

Testing TAPI Service Provider on the Client System

To test TAPI Service Provider on the client system:
1. Click the

Dial

button in the toolbar.

2. Enter a number to call in the

Number to Dial

box, and click

Place Call

.

The client extension should ring. When you pick up the phone, the system will dial
the number you entered and connect you (if the extension is configured to dial an

outside number). If this does not work, make sure your previous configurations are
correct.

Note:

Reboot the client system after any configuration changes to make sure the
changes take effect completely.

Making a Call in Microsoft Outlook

Before making a call, configure the Outlook New Call configuration.

«
...
437
438
439
440
441
...
»

Содержание ACM 6.5























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов