manualshive.com logo in svg

Altigen ACM 6.5, Руководство администратора, Страница: 131 / 502

Поделиться
Скачать
Altigen ACM 6.5 Скачать руководство пользователя страница 131

MAXCS ACM 6.5 Administration Manual 117

C

H A P T E R

10

Application Extension Configuration

The application extension is an extension pilot number that allows an SDK-based add-
on application to log into the system and establish a communication channel to control 
trunk channels and interact with the system core PBX switching and voice processing 

service. 
Typical applications that use an application extension are:

•

IVR

•

Outbound dialer

•

Inbound call routing logic for a special business application

To connect an SDK-based add-on application, you need:

•

An APC license (concurrent session) 

•

A separate application extension to log in to for each application

For more information about SDK, please send e-mail to [email protected].

Application Extension Setup

Note:

Before you begin, make sure a 

Trunk Control APC SDK Session

 license is 

registered and activated for your system. You can find this information in 

License

 

> 

License Information

.

To access the 

Application Extension Configuration

 window, select 

System >

 

Application Ext Configuration

. The configuration window opens:

Содержание ACM 6.5























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов