Altigen ACM 6.5 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 502

Altigen ACM 6.5 Скачать руководство пользователя страница 39

System Requirements and Installation

MAXCS ACM 6.5 Administration Manual 25

For Online Help

•

Internet Explorer 6.0 or higher browser.

Email server integrations

The following third- party Email Server integrations are supported:

•

Microsoft Exchange Server 2003

•

Microsoft Exchange Server 2007 R2

CPU, Memory, and HDD Requirements

The following table lists the minimum requirements for a single system.

MAXCS Licenses

In MAXCS 6.5 Update1, most client licenses are available in both concurrent session
mode and seat-based mode. Both types can be mixed in a MAXCS system.
The following licenses are available for

all AltiGen 6.5 systems

:

Number of

Triton
boards per
system

CPU
Type

Available
Memory

Hard Disk
Controller

Power
Supply

5V
Require-
ment

12 V
Require-
ment

1-3

1.2 GHz
Celeron M

512 MB

IDE RAID

Single 300W

15A

6A or
better

4-6

1.2 GHz
Celeron M

512 MB

IDE RAID

Single 400W
or Dual 400W
load sharing
recommended

20A

16A

7-15

3.0 GHz
Pentium IV

1 GB

IDE RAID

Dual 400W
with load
sharing
required

40A

20A

License Type

License Model

MAXCS ACM

Per system

MAXCS ACC

Per system

MaxCommunicator

Per seat or per session

AltiConsole

Per session

MaxAgent

Per seat or per session

MaxSupervisor

Per seat or per session

IPTalk

Per seat or per session

MaxCall

Per seat or per session

TAPI

Per extension configuration

SIP Trunk

Per activated SIP trunk

3rd Party SIP Device

Per seat registering as an IP extension (non-concurrent)

Enterprise Manager

Per server license

«
...
37
38
39
40
41
...
»

Содержание ACM 6.5























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов