Altigen ACM 6.5 Скачать руководство пользователя страница 202

Страница: 202 / 502

Configuring Out Call Routing

188

MAXCS ACM 6.5 Administration Manual

•

You would like to block a dialing pattern in addition to system restriction setting.

Dialing patterns are exceptions. If you can, minimize the number of dialing pattern
entries. Most companies don’t need to create dialing patterns.

To create a dialing pattern

1. Click the

Dialing Pattern

tab on the Out Call Routing Configuration window.

Figure 3. Out Call Routing Configuration,

Dialing Pattern

tab

2. Click the

Add

button. The following dialog box appears:

3. Type in the prefix and pattern length, and click

4. Assign routes to this prefix by selecting routes from the drop-down lists in the Route

Priority section of the

Dialing Pattern

tab.

5. If this is a restricted number or pattern, skip step 4 and check the

Disallow this

dialing pattern

check box.

To delete a dialing pattern

Select the pattern you want to delete, and click the

Delete

button.

Содержание ACM 6.5























































































































































































































































































































































































































































































































Результаты поиска

Содержание ACM 6.5

Отзывы:

Altigen ACM 6.5, Руководство администратора, Страница: 202 / 502

Результаты поиска

Содержание ACM 6.5

Отзывы: