Altigen ACM 6.5 Скачать руководство пользователя страница 159

Страница: 159 / 502

Incoming Call Routing

MAXCS ACM 6.5 Administration Manual 145

Incoming Call Routing

To set incoming call routing for a trunk, select the trunk on the

General

tab, then click

the

In Call Routing

tab in the

Trunk Configuration

window. The trunk location

appears in the title bar.

Figure 14. Trunk Configuration, In Call Routing tab

Regular Trunk Calls

For each trunk—or using

Apply to

to apply the settings to multiple trunks—you can set

routing for the three time periods defined in the

System Configuration

window,

Business Hours

tab (“Setting Business Hours” on page 54):

•

During Business Hours

•

Outside Business Hours

•

Non Workdays

Within each of these three time slots, you have the following routing options for incoming
calls:

•

Route to an extension selected in the drop-down list

•

Route to an auto attendant number selected in the drop-down list

•

Route to a Line Park line selected in the drop-down list (see “Line Park Configuration”
on page 275 for more detail)

•

Route to the operator

Web IP Calls

For web IP calls, you can set routing for the three time periods defined in the

System

Configuration

window,

Business Hours

tab (“Setting Business Hours” on page 54):

•

During Business Hours

Содержание ACM 6.5























































































































































































































































































































































































































































































































Результаты поиска

Содержание ACM 6.5

Отзывы:

Altigen ACM 6.5, Руководство администратора, Страница: 159 / 502

Результаты поиска

Содержание ACM 6.5

Отзывы: