Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 17 / 58

507961-01

Page 17 of 58

Issue 2128

1. Seal any unused openings in the common venting

system.

2. Inspect the venting system for proper size and

horizontal pitch. Determine that there is no blockage,

restriction, leakage, corrosion, or other deficiencies

which could cause an unsafe condition.

3. Close all building doors and windows and all doors

between the space in which the appliances remaining

connected to the common venting system are located

and other spaces of the building. Turn on clothes

dryers and any appliances not connected to the

common venting system. Turn on any exhaust fans,

such as range hoods and bathroom exhausts, so they

will operate at maximum speed. Do not operate a

summer exhaust fan. Close fireplace dampers.

4. Follow the lighting instructions. Turn on the appliance

that is being inspected. Adjust the thermostat so that

the appliance operates continuously.

5. After the main burner has operated for 5 minutes, test

for leaks of flue gases at the draft hood relief opening.

Use the flame of a match or candle.

6. After determining that each appliance connected to

the common venting system is venting properly, (step

3) return all doors, widows, exhaust fans, fireplace

dampers, and any other gas burning appliances to

their previous mode of operation.

7. If a venting problem is found during any of the

preceding tests, the common venting system must be

modified to correct the problem.

8. Resize the common venting system to the minimum

vent pipe size determined by using the appropriate

tables in Appendix G. (These are in the current

standards of the National Fuel Gas Code ANSI

Z223.1.)

Figure 22.

If this gas furnace replaces a furnace which was commonly vented

with another gas appliance, the size of the existing vent pipe for

that gas appliance must be checked. Without the heat of the original

furnace flue products, the existing vent pipe is probably oversized

for the single water heater or other appliance. The vent should be

checked for proper draw with the remaining appliance.

Exhaust Piping

Route piping to outside of structure. Continue with

installation following instructions given in piping termination

section.

Do Not discharge exhaust into an existing stack or

stack that also serves another gas appliance. If vertical

discharge through an existing unused stack is required,

insert PVC pipe inside the stack until the end is even

with the top or outlet end of the metal stack.

CAUTION

The exhaust vent pipe operates under positive pressure

and must be completely sealed to prevent leakage of

combustion products into the living space.

CAUTION

Vent Piping Guidelines

This gas furnace can be installed as either Non-Direct Vent

or a Direct Vent gas central furnace.

NOTE:

In Non-Direct Vent installations, combustion air is

taken from indoors and flue gases are discharged outdoors.

Intake and exhaust pipe sizing - Size pipe according to

Table 4 and Table 5A through Table 5C. Table 4 lists the

minimum vent pipe lengths permitted. Table 5A through

Table 5C lists the maximum pipe lengths permitted.

Regardless of the diameter of pipe used, the standard roof

and wall terminations described in section Exhaust Piping

Terminations should be used. Exhaust vent termination

pipe is sized to optimize the velocity of the exhaust gas as

it exits the termination. Refer to Table 7.

In some applications which permit the use of several

different sizes of vent pipe, a combination vent pipe may

be used. Contact Allied Air Technical Service for assistance

in sizing vent pipe in these applications.

NOTE:

The exhaust collar on all models is sized to

accommodate 2” Schedule 40 vent pipe. When vent

pipe which is larger than 2” must be used in an upflow

application, a transition must be applied at the exhaust

collar in order to properly step to the larger diameter

vent pipe. Contact Allied Air Technical Service

for more

information concerning sizing of vent systems which

include multiple pipe sizes.

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды