background image

21091-0-0606

Page 1

INSTALLATION INSTRUCTIONS 

AND OWNER’S MANUAL

GRAVITY TYPE DIRECT VENT 

WALL FURNACE

MODELS

HW075DV(N,P)-1

HW130DV(N,P)-1

HW180DV(N,P)-1

EFFECTIVE DATE

JUNE 2006

Do not store or use any gasoline or other flamma-

ble vapors and liquids in the vicinity of this or any 

other appliance.
WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not use 

any phone in your building.

•  Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

•  If you cannot reach your gas supplier, call the 

fire department.

Installation and service must be performed by a 

qualified installer, service agency or the gas sup-

plier.

WARNING: If the information in this manual 

is not followed exactly, a fire or explosion may 

result, causing property damage, personal in-

jury or loss of life.

INSTALLER: Leave this manual with the appli-

ance.
CONSUMER: Retain this manual for future ref-

erence.

This appliance may be installed in an aftermar-

ket,  permanently  located,  manufactured  home 

(USA only) or mobile home, where not prohibited 

by state or local codes.

This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gasses, unless a cer-

tified kit is used.

WARNING: If not installed, operated and main-

tained in accordance with the manufacturer’s in-

structions, this product could expose you to sub-

stances in fuel or from fuel combustion which can 

cause death or serious illness.

DO  NOT  RETURN  THIS  PRODUCT  TO  THE 

STORE WHERE YOU PURCHASED IT. IF YOU 

ARE MISSING PARTS, OR HAVE ANY PROB-

LEMS,  CONTACT  EMPIRE  COMFORT  SYS-

TEMS, INC. AT (877) 459-1583.

Summary of Contents for HW075DVN-1





























Reviews: