background image

DIRECT VENT 

WALL FURNACE

STANDARD MODELS:

HWDV081(N,P)-1

HWDV150(N,P)-1

MODELS WITH BLOWER:

HWDV081B(N,P)-1

HWDV150B(N,P)-1

This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA only), 

or mobile home, where not prohibited by state or local 

codes.
This appliance is only for use with the type of gas 

indicated on the rating plate. This appliance is not 

convertible for use with other gases, unless a certified 

kit is used.

INSTALLATION

INSTRUCTIONS AND

OWNER'S MANUAL

WARNING: If not installed, operated, and maintained 

in accordance with the manufacturer's instructions, 

this product could expose you to substances in fuel 

or from fuel combustion which can cause death or 

serious illness.

DO NOT RETURN THIS PRODUCT TO THE STORE 

WHERE YOU PURCHASED IT. IF YOU ARE MISS-

ING PARTS, OR HAVE ANY PROBLEMS, CONTACT  

EMPIRE COMFORT SYSTEMS INC. AT (877) 459-1583.

GAS-FIRED

Installer: 

Leave this manual with the appliance.

Consumer:  Retain this manual for future refer-

ence.

WARNING: If the information in these instruc-

tions are not followed exactly, a fire or explosion 

may result causing property damage, personal in-

jury or loss of life.

—  Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

—  WHAT TO DO IF YOU SMELL GAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use 

any phone in your building.

  •  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions.

 

•  If you cannot reach your gas supplier, call the 

fire department.

—  Installation and service must be performed by a 

qualified installer, service agency or the gas sup

-

plier.

Page 1

Summary of Contents for HWDV081

















































Reviews: