Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 43 / 58

507961-01

Page 43 of 58

Issue 2128

Sequence of Operation

Heating

On a call for heat from the room thermostat, the control

board performs a 1 second self check. Upon confirmation

that the pressure switch contacts are in an open position,

the control energizes the combustion blower on high

speed. The control then checks for adequate combustion

air by making sure the low-fire pressure switch contacts

are closed.

The igniter energizes and is allowed to warm up for 20

seconds before the gas valve energizes on 1st stage

and burners ignite. 45 seconds after the control confirms

ignition has occurred, the control drops the combustion

blower to low speed.

The circulating blower ramps up to 50% of 1st stage

heat speed and operates at that speed for one minute

(including ramp up time), then at 75% of 1st stage heat

speed for an additional minute. After that, the circulating

blower operates at full 1st stage heat speed until either

the heat call is satisfied or the thermostat initiates a call for

2nd stage heat. On a call for 2nd stage heat, the control

energizes the circulating air blower on full CFM 2nd stage

heat.

If the automatic heat staging option is being used the

furnace does not switch to 2nd stage heat in response

to a call from the thermostat but instead operates at 1st

stage heat for the duration of the selected time before

automatically switching to 2nd stage heat.

When the call for heat is satisfied, the gas valve and

combustion air blower shut down. The control board shuts

off the gas valve and runs the combustion blower for an

additional 15 seconds. The circulating air blower continues

to run for 2 minutes at 82% of the selected heating speed

(low fire or high fire) before ramping down.

In the event the unit loses ignition, the control will attempt

to recycle up to five times before it goes into a 1 hour

lockout. Lockout may be manually reset by removing

power from the control for more than 1 second or removing

the thermostat call for heat for more than 3 seconds.

If during a heating cycle the limit control senses an

abnormally high temperature and opens, the control board

de-energizes the gas valve and the combustion blower

while the circulating blower ramps up to 2nd stage heat

speed. The circulating blower remains energized until the

limits are closed.

Fan On

When the thermostat is set for continuous fan operation

and there is no demand for heating or cooling, a call for fan

closes the R to G circuit and the circulating blower motor

runs at 38% of the selected cooling CFM until switched off.

When the call for fan is turned off, the control de-energizes

the circulating blower.

Cooling

The unit is set up at the factory for single stage cooling. For

two stage cooling operation, clip the jumper wire located

between the Y to Y2 terminals on the integrated ignition/

blower control board.

If the active dehumidification feature is enabled, the

circulating blower runs at 70% of the selected cooling

speed as long as there is a call for dehumidification.

The system must not be in either the passive or active

dehumidification mode when charging a cooling system.

WARNING

Single Stage Cooling

A call for cooling from the thermostat closes the R to Y

circuit on the integrated ignition/blower control board. The

control waits for a 1-second delay before energizing the

circulating blower to 82% of the selected cooling CFM

(passive dehumidification mode). After 7.5 minutes, the

circulating blower automatically ramps up to 100% of

the selected cooling airflow. When the call for cooling is

satisfied, the circulating blower ramps back down to 82%

of the selected cooling airflow for 1 minute, then shuts off.

Two Stage Cooling

A call for 1st stage cooling from the thermostat closes the

R to Y circuit on the control board. The control waits for a

1-second delay before energizing the circulating blower.

The blower motor runs at 57% of the selected air flow

for the first 7.5 minutes of the 1st stage cooling demand

(passive dehumidification mode). After 7.5 minutes, the

blower motor runs at 70% of the selected cooling air flow

until 1st stage cooling demand is satisfied.

A call for 2nd stage cooling from the thermostat closes

the R to Y2 circuit on the control board. The blower motor

ramps up to 100% of the selected cooling air flow. When

the demand for cooling is met, the blower ramps down to

Y1 until satisfied, then ramps down to 57% for 1 minute,

then turns off.

Heat Pump

For heat pump operation, clip the jumper wire located

below the O terminal on the integrated ignition/blower

control board. In heat pump mode, a call for heat will

result in the circulating air blower operating at the selected

cooling airflow after a brief ramp-up period.

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды