Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 40 / 58

507961-01

Page 40 of 58

Issue 2128

Electrical

ELECTROSTATIC DISCHARGE (ESD)

Precautions and Procedures

Electrostatic discharge can affect electronic components.

Take precautions during furnace installation and service

to protect the furnace’s electronic controls. Precautions

will help to avoid control exposure to electrostatic

discharge by putting the furnace, the control and the

technician at the same electrostatic potential. Neutralize

electrostatic charge by touching hand and all tools on

an unpainted unit surface, such as the gas valve or

blower deck, before performing any service procedure.

CAUTION

Figure 63.

Interior Make-Up Box Installation

Figure 64.

Interior Make-Up Box Installation

The unit is equipped with a field makeup box. The makeup

box may be moved to the right side of the furnace to

facilitate installation. Seal unused openings on left side

with plugs removed from right side. Secure the excess wire

to the existing harness to protect it from damage.

Refer to Figure 72 for field wiring and Figure 73 for

schematic wiring diagram and troubleshooting.
1. The power supply wiring must meet Class I restrictions.

Protected by either a fuse or circuit breaker, select

circuit protection and wire size according to unit

nameplate.

NOTE:

Unit nameplate states maximum current draw.

Maximum over current protection allowed is shown in

Table 10.

2. Holes are on both sides of the furnace cabinet to

facilitate wiring.

3. Install a separate (properly sized) disconnect switch

near the furnace so that power can be turned off for

servicing.

Table 9.

Capacity

Maximum Over-Current

Protection (Amps)

045B

, 070B

, 090C

090C16,

090C20

, 110C16,

110C20

, 135D

4. Before connecting the thermostat, check to make sure

the wires will be long enough for servicing at a later

date. Make sure that thermostat wire is long enough to

facilitate future removal of blower for service.

5. Complete the wiring connections to the equipment.

Use the provided unit wiring diagram and the field

wiring diagram shown in Figure 72. Use 18 gauge

wire or larger that is suitable for Class II rating for

thermostat connections.

6. Electrically ground the unit according to local codes or,

in the absence of local codes, according to the current

National Electric Code (ANSI/NFPA No. 70). A green

ground wire is provided in the field make-up box.

NOTE:

This furnace contains electronic components

that are polarity sensitive. Make sure that the furnace

is wired correctly and is properly grounded.

7. One line voltage “ACC” 1/4” spade terminal is provided

on the furnace integrated control. Any electronic air

cleaner or other accessory rated up to one amp can

be connected to this terminal with the neutral leg of the

circuit being connected to one of the provided neutral

terminals. This terminal is energized when the indoor

blower is operating.

8. One line voltage “HUM” 1/4” spade terminal is provided

on the furnace integrated control. Any humidifier rated

up to one amp can be connected to this terminal

with the neutral leg of the circuit being connected to

one of the provided neutral terminals. This terminal

is energized in the heating mode whenever the

combustion air inducer is operating.

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды