Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 25 / 58

507961-01

Page 25 of 58

Issue 2128

Figure 32.

Equipment in Confined Space

(Inlet Air from Ventilated Crawlspace and Outlet Air to

Outside)

Roof Terminated

Exhaust Pipe

Furnace

Ventilation

Louvers

(Crawl Space)

*Intake Debris Screen Provided

Inlet Air

Minimum

12 in. (305mm)

above Crawl

Space Floor

Coupling or

3 in. to 2 in.

Transition

(Field Provided)

* See Maximum Vent Lengths table

NOTE-The inlet and outlet air openings shall each have a

free area of at least one square inch per 4,000 Btu (645mm

per 1.17kW) per hour of the total input rating of all equipment

in the enclosure.

General Guidelines for Vent Terminations

In Non–Direct Vent applications, combustion air is taken

from indoors and the flue gases are discharged to the

outdoors. This furnace is then classified as a non–direct

vent, Category IV gas furnace.

In Direct Vent applications, combustion air is taken from

outdoors and the flue gases are discharged to the outdoors.

The furnace is then classified as a direct vent, Category IV

gas furnace.

In both Non–Direct Vent and Direct Vent applications, the

vent termination is limited by local building codes. In the

absence of local codes, refer to the current National Fuel

Gas Code ANSI Z223-1/NFPA 54 in U.S.A., and current

CSA-B149 Natural Gas and Propane Installation Codes in

Canada for details.

In Direct Vent applications, the vent termination is limited

by local building codes. In the absence of local codes,

refer to the current National Fuel Gas Code ANSI Z223-1/

NFPA 54 in U.S.A., and current CSA-B149 Natural Gas

and Propane Installation Codes in Canada for details.

Position termination according to location given in Figure

34 and Figure 35. In addition, position termination so it

is free from any obstructions and 12” above the average

snow accumulation.

At vent termination, care must be taken to maintain

protective coatings over building materials (prolonged

exposure to exhaust condensate can destroy protective

coatings). It is recommended that the exhaust outlet not be

located within 6 feet (1.8 m) of a condensing unit because

the condensate can damage the painted coating.

NOTE:

See Table 6 for maximum allowed exhaust pipe

length without insulation in unconditioned space during

winter design temperature below 32° F (0° C). If required,

exhaust pipe should be insulated with 1/2” (13 mm),

Armaflex or equivalent when run through an unconditional

area. In extremely cold climate areas with temperature

below 20° F (6.7° C) it is recommended that, 3/4” (19 mm)

Armaflex or equivalent be used. Insulation on outside

runs of exhaust pipe should be painted or wrapped to

protect insulation from deterioration in accordance with

the insulation manufacturers recommendation. Exhaust

pipe insulation may not be necessary in some specific

applications.

NOTE:

During extremely cold temperatures, below

approximately 20° F (6.7° C), units with long runs of vent

pipe through unconditioned space, even when insulated,

may form ice in the exhaust termination that prevents the

unit from operating properly. Longer run times of at least 5

minutes will alleviate most icing problems. Also, a heating

cable may be installed on exhaust piping and termination

to prevent freeze-ups. Heating cable installation kits are

available see unit specification sheets for part numbers.

Do not use screens or perforated metal in exhaust

terminations. Doing so will cause freeze-ups and may

block the terminations.

IMPORTANT

For Canadian Installations Only:

In accordance to CSA International B149 installation

codes, the minimum allowed distance between the

combustion air intake inlet and the exhaust outlet of

other appliances shall not be less than 12 inches (305

mm).

IMPORTANT

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды