Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 9 / 58

507961-01

Page 9 of 58

Issue 2128

Figure 8.

Equipment in Confined Space - All Air from

Outside

Figure 9.

Equipment in Confined Space

(Inlet Air from Ventilated Attic and Outlet Air to

Outside)

Ventilation Louvers

Inlet Air

(Minimum 12 in.

(305mm) above

Attic Floor)

Roof Terminated

Exhaust Pipe

Furnace

*Intake Debris

Screen

(Provided)

* See Maximum Vent Lengths table

NOTE-The inlet and outlet air openings shall each have a

free area of at least one square inch per 4,000 Btu (645mm

per 1.17kW) per hour of the total input rating of all equipment

in the enclosure.

When ducts are used, they shall be of the same cross-

sectional area as the free area of the openings to which

they connect. The minimum dimension of rectangular

air ducts shall be no less than 3 inches (75 mm). In

calculating free area, the blocking effect of louvers, grilles,

or screens must be considered. If the design and free area

of protective covering is not known for calculating the size

opening required, it may be assumed that wood louvers

will have 20 to 25 percent free area and metal louvers and

grilles will have 60 to 75 percent free area. Louvers and

grilles must be fixed in the open position or interlocked

with the equipment so that they are opened automatically

during equipment operation.

Figure 10.

Equipment in Confined Space

(Inlet Air from Ventilated Crawlspace and Outlet Air to

Outside)

Roof Terminated

Exhaust Pipe

Furnace

Ventilation

Louvers

(Crawl Space)

*Intake Debris Screen Provided

Inlet Air

Minimum

12 in. (305mm)

above Crawl

Space Floor

Coupling or

3 in. to 2 in.

Transition

(Field Provided)

* See Maximum Vent Lengths table

NOTE-The inlet and outlet air openings shall each have a

free area of at least one square inch per 4,000 Btu (645mm

per 1.17kW) per hour of the total input rating of all equipment

in the enclosure.

Shipping Bolt Removal

Units with 1/2 hp blower motor are equipped with three

flexible legs and one rigid leg. The rigid leg is equipped

with a shipping bolt and a flat white plastic washer (rather

than the rubber mounting grommet used with a flexible

mounting leg). See Figure 11. The bolt and washer must

be removed before the furnace is placed into operation.

After the bolt and washer have been removed, the rigid leg

will not touch the blower housing.

Figure 11.

Units with 1/2 HP

Blower Motor

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды