Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 55 / 58

507961-01

Page 55 of 58

Issue 2128

Service

ELECTRICAL SHOCK, FIRE, OR EXPLOSION

HAZARD.

Failure to follow safety warnings exactly could result in

dangerous operation, serious injury, death or property

damage.
Improper servicing could result in dangerous operation,

serious injury, death, or property damage.
Before servicing, disconnect all electrical power to

furnace.
When servicing controls, label all wires prior to

disconnecting. Take care to reconnect wires correctly.

Verify proper operation after servicing.

WARNING

At the beginning of each heating season, system should

be checked as follows by a qualified service technician:

Blower

Check the blower wheel for debris and clean if necessary.

The blower motors are pre-lubricated for extended bearing

life. No further lubrication is needed.

The blower access panel must be securely in place

when the blower and burners are operating. Gas fumes,

which could contain carbon monoxide, can be drawn

into living space resulting in personal injury or death.

WARNING

Filters

All air filters are installed external to the unit. Filters should

be inspected monthly. Clean or replace the filters when

necessary to ensure proper furnace operation. Table 1 lists

recommended filter sizes.

Exhaust and Air Intake Pipes

Check the exhaust and air intake pipes and all connections

for tightness and to make sure there is no blockage.

NOTE:

After any heavy snow, ice or frozen fog event the

furnace vent pipes may become restricted. Always check

the vent system and remove any snow or ice that may be

obstructing the plastic intake or exhaust pipes.

Electrical

1. Check all wiring for loose connections.
2. Check for the correct voltage at the furnace (furnace

operating).

3. Check amp-draw on the blower motor.

Motor Nameplate__________Actual__________

Winterizing and Condensate Trap Care

1.  Turn off power to the furnace.
2.  Have a shallow pan ready to empty condensate water.
3.  Remove the clean out cap from the condensate trap

and empty water. Inspect the trap then reinstall the

clean out cap.

Cleaning Heat Exchanger

If cleaning the heat exchanger becomes necessary,

follow the below procedures and refer to Figure 1 when

disassembling unit. Use papers or protective covering in

front of furnace while removing heat exchanger assembly.
1.  Turn off electrical and gas supplies to the furnace.
2.  Remove the burner access panel.
3.  Mark  all  gas  valve  wires  and  disconnect  them  from

valve.

4. Remove gas supply line connected to gas valve.
5. Remove sensor wire from flame sensor. Disconnect

2–pin plug from the ignitor.

6. Disconnect wires from flame rollout switches.
7. Remove four burner assembly screws at the vestibule

panel and remove gas valve /manifold and burner box

as a single unit.

8. If necessary, clean burners at this time. Follow

procedures outlined in Burner Cleaning section.

9. Remove the clean-out cap on trap and drain. Replace

cap.

10. Disconnect condensate drain line from the condensate

trap. Remove condensate trap (it may be necessary to

cut drain pipe). Remove the 1/2” NPT fitting from the

cold end header box. Disconnect drain tubes from cold

end header collector box.

11. Disconnect condensate drain tubes from flue collar.

Remove screws that secures flue collar in place.

Remove flue collar. It may be necessary to cut the

exiting exhaust pipe for removal of the fitting.

12. Loosen two clamps from flexible no-hub exhaust collar.
13. Disconnect the 2–pin plug from the combustion air

inducer. Remove screws which secure combustion

air inducer to collector box. Remove combustion air

inducer assembly. Remove ground wire.

14. Mark and disconnect all combustion air pressure

tubing from cold end header collector box.

15. Mark and remove wires from pressure switch. Remove

pressure switch. Keep tubing attached to pressure

switch.

16. Remove electrical junction box from the side of the

furnace.

17. Remove blower access panel.

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды