Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 42 / 58

507961-01

Page 42 of 58

Issue 2128

Electronic Air Cleaner

Terminals are provided on the integrated ignition/blower

control board for connection of a 120-volt electronic air

cleaner. The “EAC” terminal is energized whenever the

thermostat calls for heat, cooling, or continuous blower. See

furnace wiring diagram for specific connection information.

Variable Speed Features

This furnace is equipped with a variable speed circulation

air blower motor that will deliver a constant airflow within a

wide range of external static pressures. Other features of

this variable speed motor include:

Soft Start

The variable speed motor will slowly ramp up to normal

operating speed. This minimizes noise and increases

comfort by eliminating the initial blasts of air encountered

with standard motors.

Soft Stop

At the end of a cooling or heating cycle, the variable speed

motor will slowly ramp down after a short blower “off” delay.

If continuous blower operation has been selected, the

variable speed motor will slowly ramp down until it reaches

the airflow for that mode.

Passive and Active Dehumidification

Passive Dehumidification

For situations where humidity control is a problem, a

dehumidification feature has been built into the variable

speed motor. At the start of each cooling cycle, the variable

speed motor will run at 82% of the rated airflow for 7.5

minutes. After 7.5 minutes has elapsed, the motor will

increase to 100% of the rated airflow.

Active Dehumidification

To achieve additional dehumidification, clip the jumper

wire located below the DEHUM terminal on the integrated

ignition/blower control board and connect a humidity

control that opens on humidity rise to the DEHUM and

R terminals. The DEHUM terminal on the control board

must be connected to the normally closed contact of the

humidity control so that the board senses an open circuit

on high humidity. In this setup, the variable speed motor

will operate at a 30% reduction in the normal cooling airflow

rate when there is a call for dehumidification.

Both the passive and active dehumidification methods

described above can be utilized on the same furnace.

Circulating Airflow Adjustments

Cooling Mode

The units are factory set for the highest airflow for each

model. Adjustments can be made to the cooling airflow

by repositioning the jumper plug marked COOL – A, B, C,

D (see Figure 66). To determine what CFM the motor is

delivering at any time, count the number of times the amber

LED on the control board flashes. Each flash signifies 100

CFM; count the flashes and multiply by 100 to determine

the actual CFM delivered (for example: 10 flashes x 100 =

1000 CFM).

Heating Mode

These units are factory set to run at the middle of the

heating rise range as shown on the unit rating plate. If

higher or lower rise is desired, reposition the jumper plug

marked HEAT - A, B, C, C (see Figure 66). See Table 12

for allowable heating speeds. To determine what CFM the

motor is delivering at any time, count the number of times

the amber LED on the control board flashes. Each flash

signifies 100 CFM; count the flashes and multiply by 100

to determine the actual CFM delivered (for example: 10

flashes x 100= 1000 CFM).

Adjust Tap

Airflow amounts may be increased or decreased by 10%

by moving the ADJUST jumper plug (see Figure 66) from

the NORM position to the (+) or (-) position. Changes to the

ADJUST tap will affect both cooling and heating airflows.

The TEST position on the ADJUST tap is not used.

Continuous Blower Operation

The comfort level of the living space can be enhanced

when using this feature by allowing continuous circulation

of air between calls for cooling or heating. The circulation

of air occurs at half the full cooling airflow rate.

To engage the continuous blower operation, place the

fan switch on the thermostat into the ON position. A call

for fan from the thermostat closes R to G on the ignition

control board. The control waits for a 1 second thermostat

debounce delay before responding to the call for fan by

ramping the circulating blower up to 38% of the cooling

speed. When the call for continuous fan is satisfied, the

control immediately ramps down the circulating blower.

Figure 66. ADJUST, HEAT, and COOL Taps on

Integrated Ignition/Blower Control Board

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды