Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 5 / 58

507961-01

Page 5 of 58

Issue 2128

Building Codes

In the USA, installation of gas furnaces must conform with

local building codes. In the absence of local codes, units

must be installed according to the current National Fuel

Gas Code (ANSI Z223.1/NFPA 54). The National Fuel Gas

Code is available from the American National Standards

Institute, Inc., 11 West 42nd Street, New York, NY 10036.

In Canada, installation must conform with current National

Standard of Canada CSA-B149 Natural Gas and Propane

Installation Codes, local plumbing or waste water codes

and other applicable local codes.

In order to ensure proper unit operation in non-direct vent

applications, combustion and ventilation air supply must

be provided according to the current National Fuel Gas

Code or CSA-B149 standard.

Installed Locations

This furnace is CSA International certified for installation

clearances to combustible material as listed on the unit

nameplate and in the table in Figure 12 and Figure 18.

Accessibility and service clearances must take precedence

over fire protection clearances.

NOTE:

For installation on combustible floors, the furnace

shall not be installed directly on carpeting, tile, or other

combustible material other than wood flooring.

For installation in a residential garage, the furnace must be

installed so that the burner(s) and the ignition source are

located no less than 18 inches (457 mm) above the floor.

The furnace must be located or protected to avoid physical

damage by vehicles. When a furnace is installed in a public

garage, hangar, or other building that has a hazardous

atmosphere, the furnace must be installed according to

recommended good practice requirements and current

National Fuel Gas Code or CSA B149 standards.

NOTE:

Furnace must be adjusted to obtain a temperature

rise within the range specified on the unit nameplate.

Failure to do so may cause erratic limit operation and

premature heat exchanger failure.

This furnace must be installed so that its electrical

components are protected from water.

Installed in Combination with a Cooling Coil

When this furnace is used with cooling units (Figure 4),

it shall be installed in parallel with, or on the upstream

side of, cooling units to avoid condensation in the heating

compartment. With a parallel flow arrangement, a damper

(or other means to control the flow of air) must adequately

prevent chilled air from entering the furnace. If the damper

is manually operated, it must be equipped to prevent

operation of either the heating or the cooling unit, unless it

is in the full HEAT or COOL setting.

When installed, this furnace must be electrically grounded

according to local codes. In addition, in the United States,

installation must conform with the current National

Electric Code, ANSI/NFPA No. 70. The National Electric

Code (ANSI/NFPA No. 70) is available from the following

address:

National Fire Protection Association

1 Battery March Park

Quincy, MA 02269

In Canada, all electrical wiring and grounding for the unit

must be installed according to the current regulations of

the Canadian Electrical Code Part I (CSA Standard C22.1)

and/or local codes.

Figure 4.

Heating Unit Installed Parallel to Air Handler Unit

Heating Unit Installed Upstream of Cooling Unit

NOTE:

This furnace is designed for a minimum continuous

return air temperature of 60°F (16°C) or an intermittent

operation down to 55°F (13°C) dry bulb for cases where a

night setback thermostat is used. Return air temperature

must not exceed 85°F (29°C) dry bulb.

This furnace may be installed in alcoves, closets, attics,

basements, garages, and utility rooms in the upflow or

horizontal position.

This furnace design has not been CSA certified for

installation in mobile homes, recreational vehicles, or

outdoors.

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды