Allied 96G2UH045BV12 Скачать руководство пользователя

Страница: 41 / 58

507961-01

Page 41 of 58

Issue 2128

9. Install the room thermostat according to the instructions

provided with the thermostat. If the furnace is being

matched with a heat pump, refer to the instruction

packaged with the dual fuel thermostat.

Indoor Blower Speeds

1. When the thermostat is set to “FAN ON,” the indoor

blower will run continuously at approximately 38%

of the second stage cooling speed when there is no

cooling or heating demand. See Table 13 for allowable

continuous circulation speeds.

2. When this unit is running in the heating mode, the

indoor blower will run on the heating speed designated

by the positions of DIP switches 1 (A,B,C,D) of the

HEAT jumper plug.

3. When there is a cooling demand, the indoor blower will

run on the cooling speed designated by the positions

of DIP switches (A, B, C, D) of the COOL jumper plug.

Generator Use - Voltage Requirements

The following requirements must be kept in mind when

specifying a generator for use with this equipment:

•

The furnace requires 120 volts ± 10% (Range: 108

volts to 132 volts).

•

The furnace operates at 60 Hz ± 5% (Range: 57 Hz

to 63 Hz).

•

The furnace integrated control requires both polarity

and proper ground. Both polarity and proper grounding

should be checked before attempting to operate the

furnace on either permanent or temporary power.

•

Generator should have a wave form distortion of less

than 5% THD (Total Harmonic Distortion).

Electrical Wiring

Risk of electrical shock. Disconnect electrical power

at the circuit breaker or service panel before making

electrical connections. Failure to disconnect power

supplies can result in property damage, personal injury,

or death.

WARNING

The furnace must be grounded and wired in accordance

with local codes or, in the absence of local codes, with the

National Electrical Code ANSI/NFPA No. 70 (latest edition)

and/or CSA C22.1 Electrical Code (latest edition) if an

external electrical source is utilized.

In all instances, other than wiring for the thermostat,

the wiring to be done and any replacement of wire shall

conform with the temperature limitation for Type T wire

–63°F (35°C) rise.

Connect a sufficiently sized wire with ground to the

furnace’s line voltage connections and ground wire. Refer

to the furnace rating plate for electrical characteristics

to be used in sizing field supply wiring and overcurrent

protection.

The line voltage supply should be routed through a readily

accessible disconnect located within sight of the furnace. A

junction box on the furnace side panel is provided for line

voltage connections. Refer to the furnace wiring diagram

for specific connection information.

Proper polarity of the supply connections (“HOT” and

“NEUTRAL”) must be observed to ensure that safety

controls provide the protection intended.

A connection to the unit’s ground wire and actual earth

ground (typically a ground stake or buried steel pipe) must

be maintained for proper operation.

Thermostat

Install a room thermostat according to the instructions

furnished with it. Select a location on an inside wall that

is not subject to drafts, direct sunshine, or other heat

sources. The initial heat anticipator setting should be equal

to the total current draw of the control circuit. Low voltage

thermostat connections are to be made to the integrated

ignition/blower control board as indicated on the wiring

diagram.

Single Stage Thermostat Operation

(

96G2UHV Models)

The automatic heat staging option allows a single stage

thermostat to be used with two stage furnace models

(

96G2UHV). To activate this option, move the jumper

pin (see Figure 65) to desired setting (5 minutes or 10

minutes). The furnace will start on 1st stage heat and

stay at 1st stage heat for the duration of the selected time

before switching to 2nd stage heat.

W1 on the control board must be connected to W1 on the

thermostat.

Figure 65. Automatic Heat Staging Jumper

Humidifier

Terminals are provided on the integrated ignition/blower

control board for connection to a 120-volt humidifier. The

“HUM” terminal is energized whenever the thermostat

calls for heat. See the furnace wiring diagram for specific

connection information.

Содержание 96G2UH045BV12



























































Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды

Allied 96G2UH045BV12, Руководство по установке

Результаты поиска

Содержание 96G2UH045BV12

Отзывы:

Похожие инструкции для 96G2UH045BV12

Бренды по названию

Популярные бренды