Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 176

Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 39

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

39

Chapter

3

Install the Module

Read and understand this section before you begin to install the module.

Environment and Enclosure

For 1791ES Modules

Topic

Page

Environment and Enclosure

Prevent Electrostatic Discharge

Environmental Considerations for Use

Follow Wiring Precautions

Follow DC Power Supply Precautions

Mount the Module

Make Connections for 1791ES Modules

Make Connections for 1732ES Modules

ATTENTION:

This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications (as defined in
IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is not intended for use in residential environments and may not
provide adequate protection to radio communication services in such
environments.

This equipment is supplied as open-type equipment for indoor use. It must be
mounted within an enclosure that is suitably designed for those specific
environmental conditions that will be present and appropriately designed to
prevent personal injury resulting from accessibility to live parts. The enclosure
must have suitable flame-retardant properties to prevent or minimize the
spread of flame, complying with a flame spread rating of 5VA, or be approved
for the application if non-metallic. The interior of the enclosure must be
accessible only by the use of a tool. Subsequent sections of this publication may
contain additional information regarding specific enclosure type ratings that are
required to comply with certain product safety certifications.

In addition to this publication, see the following:

• Industrial Automation Wiring and Grounding Guidelines,

publication

, for more installation requirements.

• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the

degrees of protection provided by enclosures.

«
...
37
38
39
40
41
...
»

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов