manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 42 / 176

Поделиться
Скачать
Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 42

42

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Chapter 3

Install the Module

Environmental 
Considerations for Use

Do not use the module in locations that are subject to these conditions:

• Direct  sunlight
• Temperatures or humidity beyond the ranges noted in 

Specifications on 

page 161

• Condensation as the result of severe changes in temperature
• Corrosive or flammable gases
• Dust, especially iron dust (only 1791ES modules)
• Salts
• Water (only 1791ES modules)
• Oil or chemicals
• Shock or vibration beyond the range noted in 

Specifications on 

page 161

Do not clean the modules with these materials:

• Acetone
• Benzene
• Thinner

Follow Wiring Precautions

WARNING: 

 Connecting and Disconnecting Wiring and Cables

• When you connect or disconnect the removable terminal block (RTB) or 

power cables with field-side power applied, an electrical arc can occur. This 
could cause an explosion in hazardous location installations. Be sure that 
power is removed or the area is nonhazardous before proceeding.

• If you connect or disconnect wiring or cables while the field-side power is 

on, an electrical arc can occur. This could cause an explosion in hazardous 
location installations. Be sure that power is removed or the area is 
nonhazardous before proceeding.

• If you connect or disconnect the communication cables with power applied 

to this module or any device on the network, an electrical arc can occur. This 
could cause an explosion in hazardous location installations.

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов