Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 45

Страница: 45 / 176

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Install the Module

Chapter 3

Follow DC Power Supply
Precautions

Mount the Module

Follow these guidelines to mount the module:

• Modules can be mounted horizontally or vertically.
• Do not mount the module near any heat source that can increase the

operating temperature of the module.

• 1732ES modules meet IP65/IP67 (when marked).
• Mount catalog number 1791ES-IB16 and 1791ES-IB8XOBV4

modules in an enclosure rated IP54 (IEC60529) or higher.

ATTENTION:

To prevent electric shock, use a DC power supply that meets

these requirements:

• A DC power supply with double or reinforced insulation, for example,

according to IED/EN 60950 or EN 50178 or a transformer according to
IEC/EN 61558.

• A DC supply satisfies requirement for class 2 circuits or limited voltage/

current circuit stated in UL 508.

• Use an external power supply that is safety extra-low voltage (SELV) rated.

• Follow these precautions for safe use.

• Wire conductors correctly and verify operation of the module before placing

the system into operation. Incorrect wiring can lead to loss of safety
function.

• Do not apply DC voltages exceeding the rated voltages to the module.

• Apply properly specified voltages to the module inputs. Applying

inappropriate voltages causes the module to fail to perform its specified
function, which leads to loss of safety functions or damage to the module.

• Never use test outputs as safety outputs. Test outputs are not safety outputs.

• Note that after installation of the module, a safety administrator must

confirm the installation and conduct trial operation and maintenance.

• Do not disassemble, repair, or modify the module. This can result in loss of

safety functions.

• Use only appropriate components or devices complying with relevant safety

standards corresponding to the required safety category and safety integrity
level.

• Conformity to requirements of the safety category and safety integrity

level must be determined for the entire system.

• We recommend you consult a certification body regarding assessment of

conformity to the required safety integrity level or safety category.

• Note that you must confirm compliance with the applicable standards for

the entire system.

• Disconnect the module from the power supply before wiring. Devices

connected to the module can operate unexpectedly if wiring is performed
while power is supplied.

Содержание 1732ES-IB12XOB4

















































































































































































Результаты поиска

Содержание 1732ES-IB12XOB4

Отзывы:

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 45 / 176

Результаты поиска

Содержание 1732ES-IB12XOB4

Отзывы: