manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 164 / 176

Поделиться
Скачать
Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 164

164

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Appendix D

Specifications

 

Output leakage current, max

0.1 mA

Short circuit protection

Yes

Current, max

25 mA – current, max (to avoid fault when used as a muted lamp output)

Current, min

5 mA – current, min (at which fault indication is generated when used as a muted lamp output)

Safety output

Output types

1732ES-IB12XOBV2, 1732ES-IB8XOBV4: Current sourcing/current sinking bipolar pair
1732ES-IB12XOB4, 1732ES-IB8XOB8: Current sourcing

Output current rating (each)

1732ES-IB12XOBV2, 1732ES-IB8XOBV4: 2 A max per point, bipolar outputs
1732ES-IB12XOB4, 1732ES-IB8XOB8: 1 A max per point, sourcing outputs

On-state voltage drop, max

1.15V

Leakage current

1732ES-IB12XOB4, 1732ES-IB8XOB8: +/-0.1 mA
1732ES-IB12XOBV2, 1732ES-IB8XOBV4: +/-1.0 mA

(1)

Internal resistance from sourcing to sinking terminal

1732ES-IB12XOBV2, 1732ES-IB8XOBV4: 3.25 kΩ
1732ES-IB12XOB4, 1732ES-IB8XOB8: N/A

Short circuit detection

Yes (short high and low and cross-circuit fault detection)

Short circuit protection

Electronic

Pilot duty rating
(1732ES-IB12XOBV2, 1732ES-IB8XOBV4 only)

DC13, 2.5 A inrush

Number of outputs

Safety outputs

1732ES-IB12XOB4 module, 4 sourcing outputs
1732ES-IB12XOBV2 module, 4 bipolar outputs, (2 pairs)
1732ES-IB8XOB8 module, 8 sourcing outputs
1732ES-IB8XOBV4 module, 8 bipolar outputs (4 pairs)

Sensor power output current rating (pins 1, 3, and 5 of each 
output signal I/O connector)

2 A max per point at 40 °C (104 °F)
1 A max per point at 55 °C (131 °F)
See 

Product temperature versus sensor power current derating (per pin) on page 165

.

(1)  Includes the presence of one sourcing output stuck-high or sinking output stuck-low fault.

Table 73 - 1732ES-IB16, 1732ES-IB8XOB8, 1732ES-IB8XOBV4, 1732ES-IB12XOB4, and 1732ES-IB12XOBV2 Modules – Technical Specifications  

Attribute

Value

Table 74 -  1732ES-IB16, 1732ES-IB8XOB8, 1732ES-IB8XOBV4, 1732ES-IB12XOB4, and 1732ES-IB12XOBV2 Modules – General 

Attribute

Value

Enclosure type rating

Meets IP65/IP67 (when marked)

Product current consumption (not including Test output or 
Safety output load current)

1732ES-IB12XOBV2: 
• In power (no load): 19.2…28.8V DC, 175 mA at 24V DC
• Out power (no load): 19.2…28.8V DC, 65 mA at 24V DC
1732ES-IB12XOB4:
• In power (no load): 19.2…28.8V DC, 175 mA at 24V DC
• Out power (no load): 19.2…28.8V DC, 45 mA at 24V DC
1732ES-IB8XOB8:
• In power (no load): 19.2…28.8V DC, 165 mA at 24V DC
• Out power (no load): 19.2…28.8V DC, 65 mA at 24V DC
1732ES-IB8XOBV4:
• In power (no load): 19.2…28.8V DC, 165 mA at 24V DC
• Out power (no load): 19.2…28.8V DC, 110 mA at 24V DC
1732ES-IB16:
   In power (no load): 19.2…28.8V DC, 190 mA at 24V DC

Operating voltage range

19.2…28.8V DC (24V DC, -20…20%)

Module power connector rating

10 A max per pin

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов