manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 51 / 176

Поделиться
Скачать
Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 51

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

51

Install the Module

Chapter 3

Mount the Module in High Vibration Areas

If you mount the module in an area that is subject to shock or vibration, use a 
flat washer and a lock washer to mount the module.

Torque the mounting screws to 0.68 N•m (6 lb•in.).

Grounding the 1732ES Modules

This figure shows the grounding features for the 1732ES modules.

Functional Earth Ground for Ethernet

The mounting screw at the top of the module is for the complex Ethernet 
shield grounding features. The rectangular ‘shorting’ bar is held in place by a 
conductive screw/washer combination that connects electrically to the metal 
shields of the Ethernet connectors internal to the module.

To ground the Ethernet shields at the module, leave the factory-installed 
‘shorting’ bar with the conductive screw/washer combination in place. You 

Lock Washer

Flat Washer

Functional Earth Ground for Ethernet

Functional Earth Ground for EMC

Shorting Bar

Ethernet Shield Mounting Point

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов