manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 34 / 176

Поделиться
Скачать
Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 34

34

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Chapter 2

About the Modules

Programming Requirements 

Use the minimum software versions listed here.

CIP Safety in
EtherNet/IP Safety 
Architectures

Safety controllers control the safety outputs. Safety or standard controllers can 
control the standard outputs. Use Guard I/O modules in EtherNet/IP safety 
architectures as shown in 

Figure 14

. The Guard I/O family is a set of I/O 

modules that when connected to an EtherNet/IP safety network are suitable 
for applications up to and including:

• SIL CL 3 as defined in IEC 61508
• CAT. 4, PLe, as defined in ISO 13849-1

Figure 14 - Safety Interlocking and Control Via CIP Safety (linear and star topology)

 

Cat. No.

Studio 5000 Logix 
Designer® Version

(1)

 

(1) This version or later.

RSLogix 5000® Software Version 

(1)

(EtherNet/IP Network)

1791ES-IB16

21

16

1791ES-IB8XOBV4

1732ES-IB12XOB4

1732ES-IB12XOBV2

1732ES-IB16

18

1732ES-IB8XOB8

1732ES-IB8XOBV4

EtherNet/IP Network

ControlNet™ Network

DeviceNet™ Network

DeviceNet 
Network

EtherNet/IP Network

RSLogix™ Software
RSView® Software

ControlNet 
Network

DeviceNet 
Network

DeviceNet 
Network

Standard Communication

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов