Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 85

Страница: 85 / 176

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Configure the I/O Modules

Chapter 5

Values and States of Tags

This table shows the values and states of the tags.

Table 22 - Values and States of Tags

Data

Description

Input data

Run Mode
STANDARD

Indicates whether a device actively updates consumed data that is in one of these states.
• Run mode: 1
• Idle State: 0

Connection Faulted
STANDARD

Indicates the validity of the safety connection between the safety producer and the safety consumer.
• Valid: 0
• Faulted: 1

Safety Input Data
SAFETY

Indicates the ON/OFF status of each input circuit.
• ON: 1
• OFF: 0

Combined Safety Input Status
SAFETY

An AND of the status of all input circuits.
• All circuits are normal: 1
• An error was detected in one or more input circuits: 0

Individual Safety Input Status
SAFETY

Indicates the status of each input circuit.
• Normal: 1
• Fault (Alarm): 0

Combined Safety Output Status
SAFETY

An AND of the status of all safety output circuits.
• All circuits are normal: 1
• An error has been detected in one or more output circuits: 0

Individual Safety Output Status
SAFETY

Indicates the status of each safety output circuit.
• Normal: 1
• Fault (Alarm): 0

Muting Lamp Status
SAFETY

Indicates the status when a test output is configured as a muting lamp output.
• Normal: 1
• Fault (Alarm): 0

Safety Output Monitor
STANDARD

Monitors the outputs of the safety output circuits.
• ON: 1
• OFF: 0

Individual Test Output Status
STANDARD

Indicates the status of each of the test output circuits.
• Normal: 1
• Fault (Alarm): 0

Input Power Error Bit
STANDARD

Indicates if the field power supplied is within specification.
• Power error: 1
• Power OK: 0

Output Power Error Bit
STANDARD

Indicates if the field power supplied is within specification.
• Power error: 1
• Power OK: 0

Output data

Safety Output Data
SAFETY

Controls the safety output.
• ON: 1
• OFF: 0

Standard Output Data
STANDARD

Controls the test output when test output mode is set to a standard output.
• ON: 1
• OFF: 0

IMPORTANT

Safety denotes information the controller can use in safety-related
functions. Standard denotes additional information that must not be relied
on for safety functions.

Содержание 1732ES-IB12XOB4

















































































































































































Результаты поиска

Содержание 1732ES-IB12XOB4

Отзывы:

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 85 / 176

Результаты поиска

Содержание 1732ES-IB12XOB4

Отзывы: