Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 176

Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 149

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

149

Get Diagnostic Status from Modules by Using Explicit Messaging

Appendix A

Explicit Messages

Explicit Messaging can also be used to read individual channel status for safety
inputs, safety outputs, test outputs, and power status. You can also configure
communication error settings for test outputs.

Table 61 - Reading the Cause of the Safety Input Error

Explicit
Message

Service

Function

Command (hex)

Response (hex)

Service
Code

Class
ID

Instance
ID

Attribute ID

Data Size

Safety input
cause of error
(fault)
information
read

Get
attribute
Single

Reads the cause for the status
bit (1…n), specified by the
Instance ID, turning OFF.

0E

3D

01…n

6E

-

0: No error
01: Configuration invalid
02: External test signal error
03: Internal input error
04: Discrepancy error
05: Error in the other dual channel
input

Table 62 - Reading the Cause of the Safety Output Error

Explicit
Message

Service

Function

Command (hex)

Response (hex)

Service
Code

Class
ID

Instance
ID

Attribute ID

Data Size

Safety output
cause of error
(fault)
information

Get attribute
single

Reads the cause for the status
bit (1…n), specified by the
Instance ID, turning OFF.

0E

3B

01…n

6E

-

0: No error
01: Configuration invalid
02: Over current detected
03: Short circuit detected
04: Output ON error
05: Error in the other dual channel
output
08: Output data error
09: Short circuit detected at safety
output

Table 63 - Monitoring the Test Output Point

Explicit Message

Service

Function

Command (hex)

Response (hex)

Service
Code

Class
ID

Instance ID

Attribute ID

Data
Size

Test output
cause of error (fault)
information

Get attribute
single

Reads the cause for the
status bit (1…n), specified
by the Instance ID, turning
OFF.

0E

09

01…n

76

-

0 = No error
01: Configuration invalid
02: Overload detected
05: Output ON error
06: Undercurrent detected for
muting lamp

«
...
147
148
149
150
151
...
»

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов