Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 176

Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 52

52

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Chapter 3

Install the Module

must also mount the module to an earth-grounded, conductive surface with
conductive mounting hardware.

If you do not want to ground the Ethernet shields at the module, remove the
‘shorting’ bar and conductive screw/washer combination and mount the
module to wall or panel.

Functional Earth Ground for EMC

The mounting screw at the bottom of the module is required to be a
conductive screw for EMC compliance. Mount the module to an earth-
grounded, conductive surface by using conductive mounting hardware to make
the required connection with earth ground.

Make Connections for 1791ES
Modules

Follow these guidelines when wiring the module:

• For stranded wire, install an insulation-covered ferrule (DIN 46228-4

standard compatible-type) at the ends before you connect wires.

• Torque screws for the power connector to 0.56…0.79 N•m (5…7 lb•in).
• Torque screws for the I/O connectors to 0.5…0.56 N•m (4.5…5 lb•in).

See the Ethernet Design Considerations Reference Manual, publication

, for information about Ethernet cable.

Power Connections

See

for a description of the pins in the power connector.

Table 7 - Power Connector Pin Descriptions

TIP

If the Ethernet shields are not grounded at the module, the mounting screw
at the Ethernet end of the module is not required to make a connection with
earth ground.

Pin No.

Signal

1

Input +24V DC power

2

Input power common

3

24V DC power

(1)

(1) NC on catalog number 1791ES-IB16 modules.

4

Output power common

1

2

3

4

«
...
50
51
52
53
54
...
»

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов