manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 55 / 176

Поделиться
Скачать
Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 55

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

55

Install the Module

Chapter 3

Make Connections for 1732ES 
Modules

See the Ethernet Design Considerations Reference Manual, publication 

ENET-RM002

, for information about Ethernet cable.

Power Connections

This section describes the power connectors and recommended cables.

Table 12 - Power Connector Pin 
Description 

Table 13 - Recommended Power Cables

See 

http://www.ab.com/en/epub/catalogs/6005557/6005561/10508712/

10513424/10513435/Introduction.html

 for more information.

Power Pass Through

The power that the module requires is supplied via a 4-pin mini-style 
connector system. The module receives its required power through the male 
connector on the left. A female connector on the right is also provided so that 
power can be daisy chained from module to module.

Pin No.

Signal

1

24V DC power

(1)

(1) Not required for 1732ES-IB16 modules.

2

Input +24V DC power

3

Input power, common

4

Output power, common

(1)

Description

Cat. No.

Mini right angle female to flying leads cord set

889N-R4AFC-6F

(1)

(1) Replace -6F (1.8 m [6 ft]) with -12 (3.7 m [12 ft]) or -20 (6.1 m [20 ft]) for additional standard cable lengths.

Mini straight female to flying leads cord set

889N-F4AFC-6F

(1)

Mini right angle male to flying leads cord set

889N-E4AFC-6F

(1)

Mini straight male to flying leads cord set

889N-M4AFC-6F

(1)

Mini right angle male to right angle female patch cord

889N-R4AFNE-2

(2)

(2) Replace -2 (2 m [6.6 ft]) with -5 (5 m [16.4 ft]) or -10 (10 m [32.8 ft]) for additional standard cable lengths.

Mini straight male to straight female patch cord

889N-F4AFNM-2

(2)

IMPORTANT

Use power pass through (daisy chaining of power) only for ‘de-energize to 
trip’ (safety state = OFF) applications.

Male Input

(mates to female cable end)

Female Output

(mates to male cable end)

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов