ADT Commercial Fire & Burglary Alarm System FOCUS 200 PLUS, Инструкция по установке и настройке

Страница: 151 / 216

Section 14 – Programming
14-3
Programming Point Data
Enter the program mode by entering the Service Code at the operating panel.
< ? Enter choice:
< Lesson
Turn on >
< See alarms Reset >
< Quit More >
Action Menu #1 is displayed.
Select More three times.
< ? Enter choice:
< Sys info
ID codes >
< Name pnt/gps Load >
< Previous First >
Action Menu #4 is displayed.
Select Name pnt/gps to move to the next screen.
< ? GROUP #1
Group 1
< Prev
Change >
< Quit Next >
Group Info Screen is displayed.
Enter the point number (e.g., for point 1, enter 1; for point 25, enter
25; for point 125, enter 125).
< ? POINT 20
Pnt 020
Type 1N/Z
< Prev Change >
< Quit Next >
Point Info Screen. is displayed.
The first line shows the current name and the second line shows
the point and the type.
Note: Type 1N/Z (No Zone) indicates the point is not yet defined.
Select Next to display the info for the next point.
Select Change to edit the info for this point.
< ? POINT 20
Pnt 020
Continue >
< Back CHR Forward >
< Left POS Right >
Character Entry Screen is displayed.
The cursor is at the first letter of the current name for the point.
Use the third key down on each side to move either Back or
Forward through the alphabet. Use the bottom key on each side to
move the cursor position either Left or Right through the name.
Select Continue to save the current name displayed and advance
to the Point Type Screen.
Enter the number of the point type.
Input Point Types
01. BA Fixed (FI) 28. Janitor Keyswitch (PID only) (JAN)
02. BA Movable Instant (MI) 29. BA Keyswitch (PID only) (KEY)
03. BA Movable Delayed (MD) 30. Remote Power Supply (RPS)
04. BA Fixed Local (FL) 31. BA End Delay (PID only) (END)
05. BA Movable Instant Daytime
Annunciation (MID)
32. BA Blocklock (PID only) (BLK)
06. BA VVS (VVS) 35. Ambush Start (ABS)
07. BA Movable Instant Chime (MIC) 36. Ambush End (ABE)
08. BA Movable Delayed Chime (MDC) 60. Manual Access Pushbutton (MAP)
09. Fire (FA) 64. Exit Pushbutton (EXP)
10. Holdup Special (HUS) 65. RF Arm (ARM)
11. Holdup (HU) 66. RF Disarm (DAR)
13. Supervisory (SPV) 67. RF No Alarm Response (NAR)
Output Point Types
14. Central Station AC (CSC) 24. Holdup Suspicion (HSC)
15. Service Mode (SMC) 25. BA Remote Sonalert (RSC)
16. Telco Fault TFC) 26. BA Bell/Vault Sensor Test (TSC)
17. BA Schedule (SCC) 27. Remote Bell (PID only) (RBL)
18. BA Lights (LTC) 33. System Trouble (STC)
19. BA Fixed (FXC) 34. Point Link (PLC)
20. BA Off (OFC) 37. BA Access (ACC)
21. Fire (FAC) 38. Horn/Strobe (SIM Only) (HST)
22. Supervisory (SPC) 59. Access Denied (ACD)
23. Holdup (HUC)
< ? FRONT DOOR 20
Type N / Z
Continue >
Type – 0 0
< Quit
Delete >
Select Delete to erase all the info for this point.