![background image](http://html1.mh-extra.com/html/abbott/precision-xceed-pro/precision-xceed-pro_operators-manual_450963084.webp)
12-4
Questions? Refer to Page 10-10 for Technical Support Instructions.
RSS:
RSS is an abbreviation for Reduced Symbology Set, which produces very small bar codes suitable for labeling electronic
components and healthcare devices. There are seven different types of RSS bar codes. RSS can encode at maximum 74
characters.
Important Safety Instructions
DANGER
Misuse of electrical equipment can cause electrocution, burns, fire and other HAZARDS.
•
Basic safety precautions should always be taken, including all those listed below.
•
Close supervision is necessary when equipment is used by, on, or near children, handicapped persons or
•
invalids.
READ THIS BEFORE USING THE EQUIPMENT
Do not place the equipment in liquid, nor put it where it could fall into liquid.
•
Use the equipment only for the purpose described in the instructions for use.
•
Do not use accessories which are not supplied or recommended by the manufacturer.
•
Do not use the equipment if it is not working properly, or if it has suffered any damage.
•
NOTE Examples of typical defects include:
•
damage caused by dropping the equipment;
•
damage caused by dropping the equipment into water or splashing water onto it.
Do not let the equipment come into contact with surfaces which are too hot to touch.
•
Do not place anything on top of the equipment.
•
Unless specifically instructed to do so by the instructions for use, do not drop or put anything into any opening in
•
the equipment.
Do not use the equipment out of doors.
•
KEEP THESE INSTRUCTIONS
Signal Output and Signal Input Parts
The following is recommended by UL for the “Intended signal input and signal output connections complying with this
requirement.” (UL 60601-1-1st edition)
The use of ACCESSORY equipment not complying with the equivalent safety requirements of this equipment may lead
to a reduced level of safety of the resulting system. Consideration relating to the choice shall include:
Use of the accessory in the PATIENT VICINITY.
•
Evidence that the safety certification of the ACCESSORY has been performed in accordance to the appropriate IEC
•
601-1 and/or IEC 601-1-1 harmonized national standard.
Patient Vicinity (UL 60601-1-1st edition)
In areas in which patients are normally cared for, the patient vicinity is the space with surfaces likely to be contacted
by the patient or an attendant who can touch the patient. This encloses a space within the room 1.83 m (6 feet) beyond
the perimonitor of the bed (examination table, dental chair, treatment booth, and the like) in its intended location, and
extending vertically 2.29 m (7 1/2 feet) above the floor.
Other Information
The device is rated for use in oxygen-rich environments. The device is rated for continuous operation.
This device was evaluated against IEC 60601-1-2. Operation of this device may affect or be affected by other equipment
in the vicinity of the device. If an effect is observed, increase the distance between devices.
Note:
Control characters and non-alphanumeric characters (e.g. $) are displayed as spaces in the Precision
Xceed Pro Monitor. Some bar codes may contain control characters and non-alphanumeric characters.
The Bar code Type section of the MeterCom screen allows you to set all bar code data entry options for
the Operator ID. and Patient ID. The types of bar codes selected determine what codes can be scanned
into the Monitor. Refer to the Meter Component Manual for detailed information.
Chapter 12: Specifications/Limitations
Содержание Precision Xceed Pro
