ABB Sensyflow iG Скачать руководство пользователя страница 36

Страница: 36 / 60

Operation, configuration and communication

Sensyflow iG, Version 1.00

42/14-39 EN

The context-sensitive button functions are shown in the display. This allows easy operation and configu-
ration of the Sensyflow iG.

The display modes show symbols in the lower right corner of the display, indicating device status infor-
mation.

In the low-voltage versions you can use also the push-buttons for parameterizati-
on, after removing the front cover and the display cover frame.

Caution!

Take ESD precautions before touching the assemblies!

ENTER button (also shown inverted in the display)
– Access to submenus
– Input confirmation
– Browsing through several functions
– Going back up one menu level

ARROW buttons, up/down (also shown inverted in the display)
– Navigating within a menu level (main menu, submenu level 1, submenu level 2)

ARROW buttons, left/right
– Navigating within an input field

+ button
– Incrementing numerical values
– Changing characters and special characters

-||-

-| |-

Connect – a proper cyclic PROFIBUS connection is established.

Disconnect – cyclic PROFIBUS connection interrupted.

Overflow – measuring value cannot be displayed (if possible, change display unit),
output values are not effected.

Pulsating asterisk – indicates normal operating condition (measuring operation).

Simulation – simulated values and status signal are output instead of measuring
values.

Error – device indicates status signal with error. Status signals can be called up in
the SERVICE MENU.

Содержание Sensyflow iG





























































Результаты поиска

Содержание Sensyflow iG

Отзывы:

Похожие инструкции для Sensyflow iG

Бренды по названию

Популярные бренды

ABB Sensyflow iG, Руководство по эксплуатации

Результаты поиска

Содержание Sensyflow iG

Отзывы:

Похожие инструкции для Sensyflow iG

Бренды по названию

Популярные бренды