ABB Sensyflow iG Скачать руководство пользователя страница 48

Страница: 48 / 60

Operation, configuration and communication

Sensyflow iG, Version 1.00

42/14-39 EN

Submenu level 2

→

AI GAS TEMP MENU

Display indication

Designation according to PA profile
3.0

Explanation

AI TEMP STATE

Display of status message for gas temperature in hexadecimal notation (status to AI
GAS TEMP Block)
Display 0x80 … 0x83

→

OK; (see also section 7.1.2.2 and 7.1.2.3 )

TEMP PV_SCALE HIGH

PV_SCALE_HIGH

internal 100 % value, normally upper range value

TEMP PV_SCALE LOW

PV_SCALE_LOW

internal 0 % value, normally lower range value

OUT_SCALE AT 100%
OUT_SCALE_AT 100%

external 100 % value

OUT_SCALE AT 0%

OUT_SCALE_AT 0%

external 0 % value

TEMP FAILSAFE TYPE

FSAFE_TYPE

If the device detects an error by means of the status signal, one of the following two
options can be selected for the output TEMP signal:

LAST VALID VALUE the last valid measuring value

ERROR VALUE the current measuring value
ERROR SUBSTITUTION VALUE a selectable substitution value

TEMP FAIL VALUE

FSAFE_VALUE

Arbitrary numeric value as substitution for an incorrect measuring value. This is only
sent to the output if option ERROR SUBSTITUTION VALUE has been selected in
TEMP ERROR SIGNAL.

TEMP FILTER FACTOR

PV_FTIME

Filter factor for signal attenuation, adjustable between 0.2 s and 100 s

TEMP HYSTERESIS
ALARM_HYS

Hysteresis for limit value monitoring, input in the selected temperature unit
(e. g. 5 °C)

TEMP ALARM HIGH

HI_HI_LIM

Upper alarm limit; alarm is triggered if limit is exceeded by measuring value

TEMP WARNING HIGH

HI_LIM

Upper warning limit (pre-alarm); warning is issued if measuring value exceeds limit

TEMP WARNING LOW
LO_LIM

Lower warning limit (pre-alarm); warning is issued if measuring value falls below
limit

TEMP ALARM LOW

LO_LO_LIM

Lower alarm limit; alarm is triggered if measuring value falls below limit

TEMP SIMULATION

SIMULATE

Outputting TEMP simulation values ON or OFF

(incl. STATUS QUALITY and STATUS LIMIT)

(

Note: ON produces the symbol "S" in the display)

TEMP SIMUL. VALUE

Input of the TEMP simulation value

STATUS QUALITY

Simulation of the STATUS signal, selection from the signals described in section
7.1.2.2 and 7.1.2.3
GOOD OK,

GOOD UPDATE EVENT…

STATUS LIMIT

Simulation of the limit value STATUS, selection between

OK
LOW_LIMIT

HIGH_LIMIT

CONSTANT

END AI GAS TEMP

Содержание Sensyflow iG





























































Результаты поиска

Содержание Sensyflow iG

Отзывы:

Бренды по названию

Популярные бренды

ABB Sensyflow iG, Руководство по эксплуатации

Результаты поиска

Содержание Sensyflow iG

Отзывы:

Бренды по названию

Популярные бренды