manualshive.com logo in svg

ABB Sensyflow iG, Руководство по эксплуатации

Поделиться
Скачать
ABB Sensyflow iG Скачать руководство пользователя страница 38

Operation, configuration and communication

38

Sensyflow iG, Version 1.00

42/14-39 EN

7.4.2

Display modes

7.4.3

Operating modes

Display of gas temperature, flow rate, and characteristic 
curve.

Use the up/down ARROW buttons to toggle the individual 
display modes.

Flow rate display, numerically and as bar graph.

Integrator value and flow rate display.

Gas temperature display

Integrator value and device operating hours display

In STANDARD operating mode you can view the parame-
ters set, but you cannot change them. The SERVICE and 
SPECIALIST modes can be accessed by actuating 
ENTER and the up/down ARROW buttons. 

The SERVICE and SPECIALIST modes allow changes of 
the parameter settings and are protected by passwords.

The password is entered by using the left/right ARROW 
buttons (cursor position) and the + button (entering the nu-
meric value). To terminate the password input, the cursor 
must be positioned fully to the right beside the 4-digit pass-
word. Only at this cursor position the + button becomes the 
ENTER button again and can be used to exit the password 
entry mask. 

When the correct password has been entered, the confir-
mation OK is briefly displayed before displaying the opera-
ting mode that has been set.

Содержание Sensyflow iG





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды