ABB RET650 2.1 IEC Скачать руководство пользователя страница 98

Страница: 98 / 126

Check that

AutoLock

and

TripLockout

are both set to

Off

Activate shortly the set lockout (SETLKOUT) signal in the IED.

Check that the circuit breaker lockout (CLLKOUT) signal is set.

Activate shortly thereafter, the reset lockout (RSTLKOUT) signal in the IED.

Check that the circuit breaker lockout (CLLKOUT) signal is reset.

Initiate a three-phase fault.
A three-phase trip should occur and all trip outputs TRL1, TRL2, TRL3 should
be activated. Functional outputs TRIP and TR3P should be active at each fault.
The output CLLKOUT should not be set.

Activate the automatic lockout function, set

AutoLock

and repeat.

Besides the TRIP outputs, CLLKOUT should be set.

Reset the lockout signal by activating the reset lockout (RSTLKOUT) signal.

Activate the trip signal lockout function, set

TripLockout

and repeat.

All trip outputs (TRL1, TRL2, TRL3) and functional outputs TRIP and TR3P
must be active and stay active after each fault, CLLKOUT should be set.

10. Reset the lockout.

All functional outputs should reset.

11. Deactivate the TRIP signal lockout function, set

TripLockout

Off

and the

automatic lockout function, set

AutoLock

Off

10.8.1.5

Completing the test

Continue to test another function or end the test by changing the

TESTMODE

setting

Off

. Restore connections and settings to their original values, if they were changed

for testing purposes.

10.9

Monitoring

10.9.1

Gas medium supervision SSIMG

Prepare the IED for verification of settings as outlined in section

"Testing the liquid

medium supervision for alarm and lock out conditions"

and section

"Completing the

test"

in this chapter.

Check that the input logical signal

BLOCK

is logical zero and that on the local HMI,

the logical signals

PRES_ALM

PRES_LO

TEMP_ALM

and

TEMP_LO

are equal to

logical zero.

Section 10

1MRK 504 160-UEN -

Testing functionality by secondary injection

Transformer protection RET650 2.1 IEC

Commissioning manual

Содержание RET650 2.1 IEC






























































































































Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Бренды по названию

Популярные бренды

ABB RET650 2.1 IEC, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Бренды по названию

Популярные бренды