manualshive.com logo in svg

ABB RET650 2.1 IEC, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB RET650 2.1 IEC Скачать руководство пользователя страница 9

Enable forcing by using LHMI................................................ 59
Enable forcing using TESTMODE function block...................60

How to change binary input/output signals using forcing............ 60

Forcing by using LHMI........................................................... 60
Forcing by using PCM600...................................................... 62

How to undo forcing changes and return the IED to normal

operation......................................................................................64

Undo forcing by using TESTMODE component.....................64
Undo forcing by using LHMI................................................... 64
Undo forcing by using PCM600..............................................64

Section 10 Testing functionality by secondary injection...................67

Testing disturbance report................................................................67

Introduction..................................................................................67
Disturbance report settings..........................................................67
Disturbance recorder (DR).......................................................... 67
Event recorder (ER) and Event list (EL)...................................... 68

Identifying the function to test in the technical reference manual ....69
Differential protection........................................................................69

Transformer differential protection T3WPDIF..............................69

Verifying the settings.............................................................. 69
Completing the test................................................................ 70

Restricted earth-fault protection, low impedance REFPDIF .......70

Verifying the settings.............................................................. 70
Completing the test................................................................ 71

Current protection.............................................................................71

Instantaneous phase overcurrent protection 3-phase output

PHPIOC ......................................................................................71

Measuring the operate limit of set values...............................71
Completing the test................................................................ 72

Four step phase overcurrent protection 3-phase output

OC4PTOC................................................................................... 72

Verifying the settings.............................................................. 72
Completing the test................................................................ 73

Instantaneous residual overcurrent protection EFPIOC .............73

Measuring the operate limit of set values...............................74
Completing the test................................................................ 74

Four step residual overcurrent protection, (Zero sequence or

negative sequence directionality) EF4PTOC ..............................74

Four step directional earth fault protection............................. 74
Four step non-directional earth fault protection......................75
Completing the test................................................................ 75

Thermal overload protection, two time constants TRPTTR ........75

Checking operate and reset values........................................75

Table of contents

Transformer protection RET650 2.1 IEC

3

Commissioning manual

Содержание RET650 2.1 IEC































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды