manualshive.com logo in svg

ABB RET650 2.1 IEC, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB RET650 2.1 IEC Скачать руководство пользователя страница 89

Overall check in principal as above (non-directional overcurrent feature)

3.

Operate value measurement
The relevant voltage restraining value (according to setting parameter

VoltageInput

) has also to be injected from the test set and the influence on the

operate value has to be calculated when testing of the operate value is done.

4.

Operate time measurement
Definite times may be tested as above (non-directional overcurrent feature). For
inverse time characteristics the START value (to which the overcurrent ratio has
to be calculated) is the actual pickup value as got with actual restraining from the
voltage restraining quantity.

10.5.1.4 

Overcurrent feature with directionality

Please note that the directional characteristic can be set in two different ways either
just dependent on the angle between current and polarizing voltage (setting parameter

DirPrinc_OC1

 or 

DirPrinc_OC2

 set to or in a way that the operate value also is

dependent on the angle between current and polarizing voltage according to the I ·
cos(

F

) law (setting parameter 

DirPrinc_OC1

 or 

DirPrinc_OC2

 set to I · cos(

F

). This

has to be known if a more detailed measurement of the directional characteristic is
made, than the one described below.

Procedure

1.

Connect the test set for injection of three-phase currents and three-phase
voltages to the appropriate current and voltage terminals of the IED.

2.

Inject current(s) and voltage(s) in a way that relevant measured (according to
setting parameter 

CurrentInput

 and 

VoltageInput

) currents and voltages are

created from the test set.

3.

Set the relevant measuring quantity current to lag or lead (lag for negative RCA
angle and lead for positive RCA angle) the relevant polarizing quantity voltage
by an angle equal to the set IED characteristic angle (rca-dir) when forward
directional feature is selected and the 

CTstarpoint

 configuration parameter is set

to 

ToObject

.

If reverse directional feature is selected or 

CTstarpoint

 configuration parameter

is set to 

FromObject

, the angle between current and polarizing voltage shall be

set equal to rca-dir+180°.

4.

Overall check in principal as above (non-directional overcurrent feature)

5.

Reverse the direction of the injection current and check that the protection does
not operate.

6.

Check with low polarization voltage that the feature becomes non-directional,
blocked or with memory according to the setting.

10.5.1.5 

Over/Undervoltage feature

Procedure

1MRK 504 160-UEN -

Section 10

Testing functionality by secondary injection

Transformer protection RET650 2.1 IEC

83

Commissioning manual

Содержание RET650 2.1 IEC































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды