ABB RET650 2.1 IEC страница 78 Скачать руководство пользователя | Manualshive

Страница: 78 / 126

background image

Observe: Do not exceed the maximum permitted overloading of
the current circuits in the IED.

5.

Compare the measured operating current with the set value.

6.

Set the operation mode to

2 out of 3

and inject current into one of the phases.

Check - no operation.

10.4.1.2

Completing the test

Continue to test another function or end the test by changing the

TESTMODE

setting

to

Off

. Restore connections and settings to their original values, if they were changed

for testing purposes.

10.4.2

Four step phase overcurrent protection 3-phase output

OC4PTOC

Prepare the IED for verification of settings outlined in section

"Preparing the IED to

verify settings"

10.4.2.1

Verifying the settings

Verification of the non-directional phase overcurrent function is done
as instructed below, without applying any polarizing voltage.

1.

Connect the test set for current injection to the appropriate IED phases.
If there is any configuration logic that is used to enable or block any of the four
available overcurrent steps, make sure that the step under test is enabled (for
example, end fault protection).
If

1 out of 3

currents for operation is chosen: Connect the injection current to

phases L1 and neutral.
If

2 out of 3

currents for operation is chosen: Connect the injection current into

phase L1 and out from phase L2.
If

3 out of 3

currents for operation is chosen: Connect the symmetrical three-

phase injection current into phases L1, L2 and L3.

2.

Connect the test set for the appropriate three-phase voltage injection to the IED
phases L1, L2 and L3. The protection shall be fed with a symmetrical three-
phase voltage.

3.

Block higher set stages when testing lower set stages by following the procedure
described below:
3.1. Set the injected polarizing voltage slightly larger than the set minimum

polarizing voltage (default is 5% of

UBase

) and set the injection current to

lag the appropriate voltage by an angle of about 80° if forward directional
function is selected.

Section 10

1MRK 504 160-UEN -

Testing functionality by secondary injection

72

Transformer protection RET650 2.1 IEC

Commissioning manual

«
...
76
77
78
79
80
...
»

Содержание RET650 2.1 IEC































































































































Отзывы:

Нет отзывов

Похожие инструкции для RET650 2.1 IEC

Бренд: Panasonic Страницы: 36

Бренд: Engelbert Strauss Страницы: 31

Бренд: STI Страницы: 2

Бренд: Franklin Electric Страницы: 25

Бренд: Palmer Safety Страницы: 20

Protect V-CA210

Бренд: Valore Страницы: 6

Бренд: i4Technology Страницы: 8

Бренд: Basler Страницы: 706

Бренд: STI Страницы: 2

Бренд: Toshiba Страницы: 59

Бренд: Toshiba Страницы: 97

Бренд: RaidSonic Technology Страницы: 10

greenMachine HDR Evie

Бренд: Lynx Страницы: 14

Бренд: Ansell Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды