ABB RET650 2.1 IEC страница 57 Скачать руководство пользователя

Страница: 57 / 126

Section 8

Establishing connection and verifying the

IEC 61850 communication

8.1

Overview

The rear OEM ports are used for:

•

station bus (IEC 61850-8-1) communication.

For IEC 61850-8-1 redundant communication, both rear OEM ports are utilized.

8.2

Setting the station communication

To enable IEC 61850 communication the corresponding OEM ports must be
activated. The rear OEM port AB and CD is used for IEC 61850-8-1 communication.
For IEC 61850-8-1 redundant communication, both OEM port AB and CD are used
exclusively.

To enable IEC 61850 station communication:

Enable IEC 61850-8-1 (station bus) communication for port AB.
1.1. Set values for the rear ports AB.

Navigate to:

Main menu/Configuration/Communication/Ethernet

configuration/LANAB:1

Set values for

Mode

IPAddress

and

IPMask

Mode

must be set to

Normal

Check that the correct IP address is assigned to the port.

1.2. Enable IEC 61850-8-1 communication.

Navigate to:

Main menu/Configuration/Communication/Station

communication/IEC61850-8-1/IEC61850–8–1:1

Set

Operation

PortSelGOOSE

and

PortSelMMS

to the port used

(for example

LANAB

Enable redundant IEC 61850-8-1 communication for port AB and CD
2.1. Enable redundant communication.

Navigate to:

Main menu/Configuration/Communication/Ethernet

configuration/PRP:1

Set values for

Operation

IPAddress

and

IPMask

Operation

must be set to

1MRK 504 160-UEN -

Section 8

Establishing connection and verifying the IEC 61850 communication

Transformer protection RET650 2.1 IEC

Commissioning manual

Содержание RET650 2.1 IEC






























































































































Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Похожие инструкции для RET650 2.1 IEC

Бренды по названию

Популярные бренды

ABB RET650 2.1 IEC, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Похожие инструкции для RET650 2.1 IEC

Бренды по названию

Популярные бренды