ABB RET650 2.1 IEC Скачать руководство пользователя страница 83

Страница: 83 / 126

At mode

2 out of 4

the phase current setting,

IP>

can be checked by single-phase

injection where the return current is connected to the summated current input. The
value of residual (earth fault) current IN set lower than

IP>

is easiest checked in back-

up trip mode

1 out of 4

10.4.6.1

Checking the phase current operate value,

IP>

The check of the

IP>

current level is best made in

FunctionMode

Current

and

BuTripMode

1 out of 3

2 out of 4

Apply the fault condition, including START of CCRBRF, with a current below
the set

IP>

Repeat the fault condition and increase the current in steps until a trip occurs.

Compare the result with the set

IP>

Note! If

No CBPos Check

Retrip off

is set, only back-up trip can be

used to check set

IP>

10.4.6.2

Checking the residual (earth fault) current operate value

IN> set below

IP>

Check the low set

IN>

current where setting

FunctionMode

Current

and setting

BuTripMode

1 out of 4

Apply the fault condition, including START of CCRBRF, with a current just
below set

IN>

Repeat the fault condition and increase the current in steps until trip appears.

Compare the result with the set

IN>

Disconnect AC and START input signals.

10.4.6.3

Checking the re-trip and back-up times

The check of the set times can be made in connection with the check of operate values
above.

Choose the applicable function and trip mode, such as

FunctionMode

Current

and

RetripMode

CB Pos Check

Apply the fault condition, including start of CCRBRF, well above the set current
value. Measure the time from START of CCRBRF.

Check the re-trip

and back-up trip times

and

In applicable cases, the back-up trip for multi-phase start

t2MPh

and back-up trip

and

can also be checked. To check

t2MPh

, a two-phase or three-phase

start shall be applied.

1MRK 504 160-UEN -

Section 10

Testing functionality by secondary injection

Transformer protection RET650 2.1 IEC

Commissioning manual

Содержание RET650 2.1 IEC






























































































































Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Бренды по названию

Популярные бренды

ABB RET650 2.1 IEC, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Бренды по названию

Популярные бренды