ABB RET650 2.1 IEC Скачать руководство пользователя страница 85

Страница: 85 / 126

The normal mode

BuTripMode

1 out of 3

should have been verified in the tests

above. In applicable cases the modes

1 out of 4

and

2 out of 4

can be checked. Choose

the mode below, which corresponds to the actual case.

Checking the case

BuTripMode = 1 out of 4

It is assumed that the earth-fault current setting

IN>

is below phase current setting

IP>

Set

BuTripMode

1 out of 4

Apply the fault condition, including start of CCRBRF, with one-phase current
below set

IP>

but above

IN>

. The residual earth-fault should then be above set

IN>

Verify that back-up trip is achieved after set time. If selected, re-trip should also
appear.

Disconnect AC and START input signals.

Checking the case

BuTripMode = 2 out of 4

The earth-fault current setting

IN>

may be equal to or below phase-current setting

IP>

Set

BuTripMode

2 out of 4

Apply the fault condition, including start of CCRBRF, with one-phase current
above set

IP>

and residual (earth fault) above set

IN>

Verify that back-up trip is achieved after set time. If selected, re-trip should also
appear.

Apply the fault condition, including start of CCRBRF, with at least one-phase
current below set

IP>

and residual (earth fault) above set

IN>

. The current may

be arranged by feeding three- (or two-) phase currents with equal phase angle
(I0-component) below

IP>

, but of such value that the residual (earth fault)

current (3I

) will be above set value

IN>

Verify that back-up trip is not achieved.

Disconnect AC and START input signals.

10.4.6.6

Verifying instantaneous back-up trip at CB faulty condition

Applies in a case where a signal from CB supervision function regarding CB being
faulty and unable to trip is connected to input CBFLT.

Repeat the check of back-up trip time. Disconnect current and START input
signals.

Activate the input CBFLT. The output CBALARM (CB faulty alarm) should
appear after set time

tCBAlarm

. Keep the input activated.

Apply the fault condition, including start of CCRBRF, with current above set
current value.

Verify that back-up trip is obtained without intentional delay, for example
within 20ms from application of start.

1MRK 504 160-UEN -

Section 10

Testing functionality by secondary injection

Transformer protection RET650 2.1 IEC

Commissioning manual

Содержание RET650 2.1 IEC






























































































































Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Бренды по названию

Популярные бренды

ABB RET650 2.1 IEC, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Бренды по названию

Популярные бренды