ABB RET650 2.1 IEC Скачать руководство пользователя страница 99

Страница: 99 / 126

10.9.1.1

Testing the liquid medium supervision for alarm and lock out conditions

Connect binary inputs to consider gas pressure and gas density to initiate the
alarms.

Consider the analogue pressure input

PRESSURE

to initiate the alarms.

Gas pressure lock out input can be used to set

PRES_LO

signal, check the signal

status in local HMI under

Main menu/Test/Function status/Monitoring/Gas

medium supervision SSIMG/PRES_LO

Reduce the pressure level input below

PresAlmLimit

, check for

PRES_ALM

signal status in local HMI under

Main menu/Test/Function status/

Monitoring/Gas medium supervision SSIMG/PRES_ALM

Activate

BLOCK

binary input, the signals

PRES_ALM

PRES_LO

should

disappear.

Reset the

BLOCK

binary input.

Check for reset lock out input

RESET_LO

to reset

PRES_LO

lock out signal.

Conduct these steps for temperature input as well to detect and reset

TEMP_ALM

and

TEMP_LO

signals.

Continue to test another function or end the test by changing the

TESTMODE

setting to

off

10.9.1.2

Completing the test

Continue to test another function or end the test by changing the

TestMode

setting to

Off

. Restore connections and settings to their original values, if they were changed for

testing purposes.

10.9.2

Liquid medium supervision SSIML

Prepare the IED for verification of settings as outlined in section

"Completing the test"

in this chapter.

Check that the input logical signal

BLOCK

is logical zero and that on the local HMI,

the logical signals

LVL_ALM

LVL_LO

TEMP_ALM

and

TEMP_LO

are equal to

logical zero.

10.9.2.1

Testing the liquid medium supervision for alarm and lock out conditions

Connect the binary inputs to consider liquid level to initiate the alarms.

Consider the analogue level input

LEVEL

to initiate the alarms.

Liquid level lock out input can be used to set

LVL_LO

signal, check the signal

status in local HMI under

Main menu/Test/Function status/Monitoring/

Liquid medium supervision SSIML/LVL_LO

Reduce the liquid level input below LevelAlmLimit, check for

LVL_ALM

signal

status in local HMI under

Main menu/Test/Function status/Monitoring/

Liquid medium supervision SSIML/LVL_ALM

1MRK 504 160-UEN -

Section 10

Testing functionality by secondary injection

Transformer protection RET650 2.1 IEC

Commissioning manual

Содержание RET650 2.1 IEC






























































































































Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Бренды по названию

Популярные бренды

ABB RET650 2.1 IEC, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание RET650 2.1 IEC

Отзывы:

Бренды по названию

Популярные бренды