ABB REACT-3.6-TL Скачать руководство пользователя страница 6

Страница: 6 / 174

- 6 -

000456BG

1 - Introduction and general information

Safety devices .......................................................................................................................................44

Anti-Islanding ........................................................................................................................44
Ground fault of the photovoltaic panels ................................................................................44

“

STOP” button .......................................................................................................................44

REACT-BATT-AP1 state of health (SOH) .............................................................................44
Other safeguards ..................................................................................................................44

afety and accident prevention ..................................................................................................... 45

Safety information and instructions ..................................................................................................45
Hazardous areas and operations .......................................................................................................46

Residual risks .......................................................................................................................................50

Table of residual risks ...........................................................................................................50

ifting and transport ........................................................................................................................ 51

General conditions ..............................................................................................................................51
Storage of equipment...........................................................................................................................52

Special rules for storage of REACT-BATT ............................................................................52

Lifting .....................................................................................................................................................53

Equipment weight .................................................................................................................53

Transport of the equipment .................................................................................................................54

Transport of the REACT-BATT-AP1 .....................................................................................54
Overview of the “Ancillary rule” and the “1000 units rule” ....................................................54

Unpacking and checking ....................................................................................................................56

List of components supplied .................................................................................................56

nstallation ......................................................................................................................................... 58

General conditions ..............................................................................................................................58

Environmental checks ...........................................................................................................59
Installation position ................................................................................................................61

Wall installation of the REACT system ..............................................................................................62
Wall installation of the REACT-UNO alone ........................................................................................66
Connection of the energy meter (REACT-MTR) ................................................................................70

Connection of the REACT-MTR-1PH (mono-phase) ...........................................................70
Connection and configuration of the REACT-MTR-3PH
(three-phase) .........................................................................................................................72

Preliminary operations for connection of the PV generator ...........................................................74

Checking the correct polarity of the strings ..........................................................................74
Checking of leakage to ground of the photovoltaic generator ..............................................74
Selection of differential protection downstream of the inverter ............................................74

Distribution grid output connection (AC side) ..................................................................................76

Characteristics and sizing of the line cable ..........................................................................76
Load protection switch (AC disconnect switch) ....................................................................77
Connection to the AC side terminal block .............................................................................77

Back-up output connection (AC) ........................................................................................................78

Characteristics and sizing of the cable for back-up output ...................................................79
Load protection switch (AC disconnect switch) for back-up output ......................................79
Connection to back-up AC output terminal block .................................................................80

Скачано

сайта

интернет

магазина

https://axiomplus.com.ua/

Содержание REACT-3.6-TL















































































































































































Результаты поиска

Содержание REACT-3.6-TL

Отзывы:

Бренды по названию

Популярные бренды

ABB REACT-3.6-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание REACT-3.6-TL

Отзывы:

Бренды по названию

Популярные бренды