manualshive.com logo in svg

ABB REACT-3.6-TL, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB REACT-3.6-TL Скачать руководство пользователя страница 120

- 120 -

000569BG

7 - Operation

D

escription of the menus

The ABB inverters are equipped with a graphical display 

07

, consisting of 

2 lines of 16 characters each, which can be used to:

• Display the operating status of the inverter and the statistical data

• Display service messages for the operator

• Display the alarm and fault messages

• Change the inverter settings.

G

eneral information

While the inverter is operating, the display shows various items of infor-
mation on the main parameters measured, the operating conditions and 
the inverter's operating status.
The sequence of screens displayed is shown below, with a description of 
the parameters monitored.

Alarm description

Warning/Error xxx

Inverter OK

Mon 22 Jan 15:55

E-day   xxx.xkWh

$-day    xx.xEUR

E-tot   xxx.xkWh

E-par   xxx.xkWh

Pout       xxxxW
Lim XX%    Pnom

Psetpoint   xxx%

Regulation Type

COSp x.xxx     

DOWN

UP

DOWN

UP

DOWN

UP

Backup: xxxxxxx

xxxxW   XXXX

DOWN

UP

DOWN

UP

DOWN

UP

DOWN

UP

Ppk        xxxxW 

Ppk-Day    xxxxW

DOWN

UP

Vgrid       xxxV

Igrid      xx.xV

Fgrid     xx.xxHz

DOWN

UP

Riso       xx.xM©

Ileak    x.xxxxA

Vbulk       xxxV

Vbulk_m     xxxV

DOWN

UP

DOWN

UP

DOWN

UP

Vin1      xxxV 

Iin1     xx.xA

Vin2      xxxV 

Iin2     xx.xA

Pin1     xxxxW 

Pin2     xxxxW 

DOWN

UP

DOWN

UP

DOWN

UP

DOWN

UP

DOWN

UP

DOWN

UP

DOWN

UP

Vin       xxxV 

Iin      xx.xA

Pin      xxxxW 

DOWN

UP

Inverter status: The code for any malfunction will be displayed.
Date and time as set on the inverter

Presence of 

Errors/Warnings

No

Errors/Warnings

E-day: Daily energy produced 
$-day : Today's savings/earnings

Value and graphical representation of the energy fed into or taken from the grid. Power fed into grid=bars and 
arrow towards . Power taken from grid=bars and arrow towards the symbol -. Zero exchange with 
the grid= central down arrow with words ZERO NET POWER.

E-tot: Energy produced since the inverter was commissioned
E-par: Partial energy produced since the last reset

Backup:

 Backup mode set 

Pout: Instantaneous output power
Lim XX%: Limitation applied to the nominal output power

Psetpoint: Intervention threshold for the output nominal power limit set

*

*

Regulation Type: 

Mode for regulating the reactive power currently set 

COSp: Phase difference set for feeding in reactive power

Ppk:

 Maximum output power peak since the inverter was commissioned

Ppk-Day:

 Maximum daily output power peak 

Vgrid:

 Measurement of output voltage

Igrid:

 Measurement of output current

Fgrid:

 Measurement of output frequency 

Riso: Insulation resistance on DC input side (PV generator)

Ileak:

 Leakage current on DC input side (PV generator)

Vbulk:

 Internal voltage at the bulk capacitor terminals (booster circuit)

Vbulk_m:

 Internal voltage at the bulk capacitor mid-point (booster circuit)

* Present only if the value or mode have been set

Vin 1: Input voltage channel 1  

Vin: Input voltage

Iin 1: Input current channel 1  

Iin: Input current

Vin 2: Input voltage channel 2
Iin 2: Input current channel 2

Pin1: Instantaneous input power channel 1 
Pin: Instantaneous input power

Pin2: Instantaneous input power channel 2

Independent 

inputs

Parallel 

inputs

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Содержание REACT-3.6-TL















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды