manualshive.com logo in svg

ABB NPBA-01, Руководство по установке и запуску

Поделиться
Скачать
ABB NPBA-01 Скачать руководство пользователя страница 9

Chapter 1 – Introduction to This Guide

Installation and Start-up Guide for NPBA-01

1-2

Appendix A  presents the ACS 600 Actual signals, ACS 600 
parameters with the corresponding PROFIBUS parameter numbers, 
profile-specific parameters, the alternative settings and the scaling 
factors for PROFIBUS communication.

Appendix B  explains definitions and abbreviations concerning the 
PROFIBUS protocol family.

Appendix C  contains Technical Data.

Appendix D  contains a specification of the ambient conditions allowed 
during transportation, storage and use of the ACS 600’s option device.

Appendix E  includes assembly drawings that assist in placing the 
option module.

Appendix F  contains the listing for a definition program required by 
Siemens masters to configure the system for communication with the 
NPBA-01 PROFIBUS Adapter Module.

Conventions Used in 
This Guide

CDP 311

CDP 311 is a control panel used for supervising, programming and 
controlling the ACS 600 frequency converter. For further information, 
see the 

ACS 600 Programming Manual.

Communication Module

Communication Module is the parameter name/parameter selection 
name for a device through which the ACS 600 is connected to an 
external serial communication network, e.g. to an open fieldbus. The 
NPBA-01 Adapter Module is one of the fieldbus adapter modules 
available for the ACS 600. The communication with the fieldbus 
adapter is activated with Parameter 98.2 COMM.MODULE.

NPBA-01 PROFIBUS

Adapter Module

The NPBA-01 Adapter Module is one of the optional fieldbus adapter 
modules available for the ACS 600. The NPBA-01 is a device through 
which the ACS 600 is connected to a PROFIBUS serial communication 
bus. 

Parameter

A parameter is an operating instruction for the ACS 600 frequency 
converter. Parameters can be read and programmed with the CDP 311 
Control Panel, or through the NPBA-01 Module.

Related Publications

ACS 601 Installation & Start-up Manual or
ACS 602/603/ 604 Installation & Start-up Manual

ACS 600 Programming Manual.

Содержание NPBA-01





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды