manualshive.com logo in svg

ABB NPBA-01, Руководство по установке и запуску

Поделиться
Скачать
ABB NPBA-01 Скачать руководство пользователя страница 25

Chapter 5 – Programming

Installation and Start-up Guide for NPBA-01

5-6

D1, ... D6
The External control location to be used is determined by the state of 
the specified digital input. 0V DC on the selected digital input = EXT1; 
24V DC on the selected digital input = EXT2.

COMM.MODULE 

(Recommended Setting)

The selection between EXT 1 and EXT 2 is done through the 
communication module (Control Word bit 11).

11.3 EXT REF1 SELECT

This parameter defines the source of the reference for External control 
location 1 (see Parameter 11.2). 

KEYPAD
The control panel is the source of the reference.

AI1, ... , MAX (AI2, AI3)
The analogue inputs (one or more) specified by the parameter value 
are the source of the reference. For details on the use of the analogue 
inputs, see the 

ACS 600 Programming Manual.

DI3U,4D(R), ... ,DI5U,6D
The digital inputs (one or more) specified by the parameter value are 
source of the reference. For details on the digital inputs, see the 

ACS 

600 Programming Manual.

COMM.MODULE 

(Recommended Setting)

The communication module is the source of the reference.

11.6 EXT REF2 SELECT

This parameter defines the source of the reference for External control 
location 2 (see Parameter 11.2).

KEYPAD
The control panel is the source of the reference.

AI1, ... , MAX (AI2, AI3)
The analogue inputs (one or more) specified by the parameter value 
are source of the reference. For details on the use of the analogue 
inputs, see the 

ACS 600 Programming Manual.

DI3U,4D(R), ... ,DI5U,6D
The digital inputs (one or more) specified by the parameter value are 
the source of the reference. For details on the use of the digital inputs, 
see the 

ACS 600 Programming Manual.

COMM.MODULE 

(Recommended Setting)

The communication module is the source of the reference. 

12.1 CONST SPEED SEL

This parameter defines which digital inputs are used to select Constant 
Speeds.

NOT SEL 

(Recommended Setting)

Constant speed function disabled. This setting is recommended as this 
parameter overrides external reference selections.

D1 (SPEED1), ..., DI3,4,5,6
Constant speeds selected with digital inputs. For details, see the
ACS 600 Programming Manual.

Содержание NPBA-01





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды