manualshive.com logo in svg

ABB NPBA-01, Руководство по установке и запуску

Поделиться
Скачать
ABB NPBA-01 Скачать руководство пользователя страница 20

Installation and Start-up Guide for NPBA-01

5-1

Chapter 5 – Programming

Overview

This chapter explains how to program the ACS 600 parameters to 
prepare the drive for PROFIBUS communication.

For information on setting the ACS 600 parameters, read 

General 

below. For details, see the 

ACS 600 Programming Manual.

The sections 

NPBA-01 Module Activation and PROFIBUS 

Connection Configuration (page 5-3) describe how the 
communication between the ACS 600 and the NPBA-01 PROFIBUS 
Adapter Module is started.

Control Locations (starting page 5-4) deals with selecting the
NPBA-01 module as the source of Start, Stop, Direction and Reference 
signals. For information on how to select the actual signal from the 
ACS 600 to be read through the PROFIBUS link, refer to 

Analogue 

Outputs, page 5-7. The selection of the NPBA-01 module as the 
source of the Run enable signal and fault reset is described in 

System 

Control Inputs, page 5-7. For information on how to define the 
operation of the drive upon a NPBA-01 Module fault condition, see 
Fault Functions, page 5-8.

General

The operation of the ACS 600 standard software can be changed by 
adjusting the drive operating instructions called Parameters. Parameter 
values can be modified with the CDP 311 Control Panel. For 
information on the use of the control panel, see the 

ACS 600 

Programming Manual. 

Before programming, the NPBA-01 PROFIBUS Adapter Module should 
be installed according to the instructions given in Chapters 3 and 4.

Table 5-1 (next page) presents the Parameters that should be set after 
the NPBA-01 PROFIBUS Adapter Module has been mechanically and 
electrically installed. The Parameters are discussed in more detail later 
in this chapter. The default values refer to the Factory macro, and may 
differ from the default values of other macros.

Note: The proper control of the ACS 600 by the PROFIBUS Control 
Word requires that the parameters are set according to the values in 
the Recommended Settings column.

Appendix F contains the listing for a type definition program, required 
by Siemens master stations to configure the system for communication 
with the NPBA-01 PROFIBUS Adapter Module.

Содержание NPBA-01





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды