ABB NPBA-01 Скачать руководство пользователя страница 39

Страница: 39 / 68

Chapter 6 – Communication

Installation and Start-up Guide for NPBA-01

6-12

The Status Word

The Status Word is PROFIBUS Parameter No. 968. The contents of
the Status Word is presented in the following table. The text in

italics

refers to the states in Figure 6-1, page 6-14

(ACS 600/PROFIBUS

State Machine).

Table 6-4 The Status Word.

Bit

Value

Description

Ready (initialisation OK,

DRIVE READY)

Initialisation not ready or not OK

(DRIVE NOT READY)

Ready

(READY TO START)

Not ready

(STOP 1)

Ready for reference, or running

(START)

Not ready

(RUN DISABLE)

Fault condition

(FAULT)

No fault

“Coast to stop”

(STOP 2) OFF

“Coast to stop”

(STOP 2) ON

“Stop according to selected stop type”

(STOP 3) OFF

“Stop according to selected stop type”

(STOP 3) ON

DRIVE DISABLE

DRIVE NOT READY

Warning condition

No warning

Actual value equals reference value (= is within tolerance limits)

Actual value differs from reference value (= is outside tolerance limits)

ACS 600 Control location REMOTE

ACS 600 Control location LOCAL

Actual frequency value equals or is greater than supervision limit

Actual frequency value is within supervision limit

External reference 2 selected

External reference 1 selected

12 to 14

1,0

Unused

Error(s) in DDCS communication
NOTE: The information in the Status Word is not updated.

DDCS communication (ACS 600 – NPBA-01) OK

Содержание NPBA-01




































































Результаты поиска

Содержание NPBA-01

Отзывы:

Бренды по названию

Популярные бренды

ABB NPBA-01, Руководство по установке и запуску

Результаты поиска

Содержание NPBA-01

Отзывы:

Бренды по названию

Популярные бренды