manualshive.com logo in svg

ABB NPBA-01, Руководство по установке и запуску

Поделиться
Скачать
ABB NPBA-01 Скачать руководство пользователя страница 23

Chapter 5 – Programming

Installation and Start-up Guide for NPBA-01

5-4

51.1 MODULE TYPE

This parameter shows the module type as detected by the ACS 600. 
The value cannot be adjusted by the user.  

51.2 PROFIBUS MODE

This parameter defines the operating mode of the PROFIBUS 
connection.

FMS
The NPBA-01 module uses the PROFIBUS-FMS protocol.

DP-PPO1, ..., DP-PPO5
The NPBA-01 module uses the PROFIBUS-DP protocol. This 
parameter also selects the PPO message type (see Chapter 6
for PPO message types).

51.3 STATION NUMBER

Each device on the PROFIBUS link must have a unique station 
number. This parameter is used to define a station number for the ACS 
600 unit it is connected to. Allowable values are 2 to 126 inclusive.

51.4 BIT RATE SELECT

This parameter shows the transfer rate used in the PROFIBUS link. 
The default value is AUTO. With AUTO selected, the transfer rate is 
detected automatically.

51.5 WRITE PPO

DATA SET SEL

This parameter defines the number of the data set the PPO message 
process information is written to. This data set is transmitted in PPO 
message parts PD1 to PD3 (see Table 6-2, page 6-7). This parameter 
is effective only when PPO Type 2, 4 or 5 is used.

51.6 READ PPO

DATA SET SEL

This parameter defines the number of the data set the PPO message 
process information is read from. This data set is transmitted in PPO 
message parts PD1 to PD3 (see Table 6-2, page 6-7). This parameter 
is effective only when PPO Type 2, 4 or 5 is used.

Note:  PPO Type 5 is available in PROFIBUS-DP mode only.

Control Locations

The ACS 600 drive can receive control information from multiple 
sources including digital inputs, analogue inputs, the CDP 311 Control 
Panel and a communication module (e.g. NPBA-01). The control signal 
sources for the drive are selected with the parameters in Parameter 
Group 10 START/STOP/DIR and in Parameter Group 11 
REFERENCE SELECT. The parameters can be altered only with the 
drive stopped.

10.1 EXT1 STRT/STP/DIR

This parameter defines the source of the Start, Stop and Direction 
commands for External control location 1 (see Parameter 11.2). 

NOT SEL
No source is selected for the Start, Stop and Direction commands.

Содержание NPBA-01





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды